Maxima Forums

 
Page 1 of 5
1
2
3
Last »
Search: Posts Made By: tom_98se
Showing results 1 to 25 of 124
Search took 0.16 seconds.
Forum: 4th Generation Classifieds (1995-1999)
04-21-2015, 07:28 PM
Replies: 3
Views: 591
Posted By tom_98se

Bump, all parts are still available. Make me an...

Bump, all parts are still available. Make me an offer so I can get these out of the garage.

Thanks,
TOM
Forum: Audio/Video/Electronics
04-21-2015, 07:27 PM
Replies: 1
Views: 1,753
Posted By tom_98se

Bump, the box & amp are still available. Make me...

Bump, the box & amp are still available. Make me an offer so I can get these out of the garage.

Thanks,
TOM
Forum: Audio/Video/Electronics
04-11-2015, 09:23 PM
Replies: 1
Views: 1,753
Posted By tom_98se

FS: JL Audio stealthbox (4th gen) & e6450 six-channel amp

Hi all. Selling some older Maxima parts. My car is long gone and I'm looking to move a few things out of the garage:

JL Audio stealthbox (4th gen): $100
The original JL stealthbox, ready for your...
Forum: 4th Generation Classifieds (1995-1999)
04-11-2015, 09:10 PM
Replies: 3
Views: 591
Posted By tom_98se

FS: SE shocks/struts/springs & leather steering wheel

Hi all. Selling some older Maxima parts. My car is long gone and I'm looking to move a few things out of the garage:

Suspension parts: $100
I bought some used SE shocks, struts & springs from...
Forum: Maximas for Sale / Wanted
06-04-2013, 09:41 PM
Replies: 1
Views: 1,084
Posted By tom_98se

Bump for price reduction. Let me know if you have...

Bump for price reduction. Let me know if you have questions/comments.

Thanks,
TOM
Forum: Maximas for Sale / Wanted
05-27-2013, 03:28 PM
Replies: 1
Views: 1,084
Posted By tom_98se

1998 Maxima SE 5-speed 159k | Rosewood w/ Tan Cloth

(Reposting due to my noob mistake of putting the price in the thread title!)

Hello forum! After a decade of faithful service it is time to sell the Maxima. I bought it from a family member in...
Forum: 4th Generation Maxima (1995-1999)
01-21-2007, 09:29 AM
Replies: 18
Views: 2,069
Posted By tom_98se

Tie-rod ends

Ditto on the tie-rod ends. I had a wicked popping / thunking coming from the right-front. After a new endlink bushing, lower control arm & ball joint, we found the problem - one inner tie rod end was...
Forum: Audio and Electronics
02-03-2005, 04:57 AM
Replies: 4
Views: 518
Posted By tom_98se

Thanks for the lead. But assuming the amp is...

Thanks for the lead. But assuming the amp is something like their 16-MC600D (which is in their spec sheet, but not the 16-MCH600), it's almost 18" long. I'm just not sure how I could fit that under...
Forum: Audio and Electronics
02-02-2005, 07:24 PM
Replies: 4
Views: 518
Posted By tom_98se

Four-channel amp under passenger seat?

Hey, I'm looking for a small, quality four-channel amp to mount under the passenger seat of my 4gen. My plan is to run it in tri-mode, with two channels powering front components and the other two...
Forum: 4th Generation Maxima (1995-1999)
12-17-2004, 04:50 AM
Replies: 8
Views: 2,779
Posted By tom_98se

I absolutely agree, but I'm running out of...

I absolutely agree, but I'm running out of components to replace. The sound is definitely coming from the right front, so I've narrowed that down. I replaced the whole control arm with ball joint,...
Forum: 4th Generation Maxima (1995-1999)
12-15-2004, 08:06 PM
Replies: 8
Views: 2,779
Posted By tom_98se

What do you need (in terms of specialty tools) to...

What do you need (in terms of specialty tools) to replace inner tie-rod ends? I have a rattle from my right front that just won't disappear. I've got probably $400 into a new control arm and a...
Forum: 4th Generation Maxima (1995-1999)
10-24-2004, 08:11 AM
Replies: 3
Views: 509
Posted By tom_98se

PCV valve?

I had some idle troubles after I changed a PCV valve @ the 60k service. They would drop to 300-500rpm while shifting (I have a 5-speed.) So I replaced it again and my idle problems went away....
Forum: 4th Generation Maxima (1995-1999)
09-07-2004, 06:14 PM
Replies: 10
Views: 507
Posted By tom_98se

I smell something. Seems like the misspellings...

I smell something. Seems like the misspellings are a little too carefully crafted. Preform? Haeve? Eek, our options are A) someone's being funny, or B) English teachers are crying. :gapteeth:
Forum: 4th Generation Maxima (1995-1999)
09-07-2004, 06:05 PM
Replies: 15
Views: 30,646
Posted By tom_98se

It also depends if you're replacing the whole...

It also depends if you're replacing the whole control arm or just having a new ball joint pressed in. While the joint itself is like $30, a new control arm is around $200. I was charged two hours of...
Forum: 4th Generation Maxima (1995-1999)
09-06-2004, 04:42 PM
Replies: 9
Views: 622
Posted By tom_98se

I would like to note that the Motovate...

I would like to note that the Motovate instructions are not perfect for all years. IE, my '98 has 19mm bolts on the torque member, not 17mm. I found that tidbit after taking the car half-apart. And...
Forum: 4th Generation Maxima (1995-1999)
09-03-2004, 04:12 PM
Replies: 5
Views: 543
Posted By tom_98se

PCV valve? I had erratic idle problems, too high,...

PCV valve? I had erratic idle problems, too high, then too low. It was especially annoying to have my RPM's drop to 300 or 400 as I put the clutch in when turning, etc.

It all started after I had...
Forum: 4th Generation Maxima (1995-1999)
09-02-2004, 06:28 PM
Replies: 99
Views: 4,143
Posted By tom_98se

Lookin' good

Looks nice. I like the fat spokes on there, a nice contrast to the skinny-spoked rims that are all over the place. A little beef to them!

And the gap is no big deal. It's certainly less than the...
Forum: 4th Generation Maxima (1995-1999)
09-01-2004, 07:54 PM
Replies: 20
Views: 6,728
Posted By tom_98se

Trust but verify...

Replacing the strut bearing is a popular suggestion, but I had the same problem and solved it by replacing the right-side swaybar endlink bushing. The strut bearing was NOT defective. What made...
Forum: 4th Generation Maxima (1995-1999)
07-31-2004, 07:40 AM
Replies: 10
Views: 623
Posted By tom_98se

Ack, I akready had your site bookmarked but...

Ack, I akready had your site bookmarked but didn't bother to look again. Your site should be a sticky (unless it already is.) Excellent breakdown - Looks like the Quietstops are going to be the...
Forum: 4th Generation Maxima (1995-1999)
07-30-2004, 09:14 PM
Replies: 10
Views: 623
Posted By tom_98se

Brake pads, which to get?

Looking to replace my front brakes pretty soon. I'm looking for daily-driver performance, minimal dust & decent longevity.

Aside from the hardware kit (shims, etc.) I can't decide which pads to go...
Forum: 4th Generation Maxima (1995-1999)
07-30-2004, 08:59 PM
Replies: 2
Views: 498
Posted By tom_98se

Hooah. I had a pop/clunk coming from my...

Hooah. I had a pop/clunk coming from my right-front for almost two years. Unfortunately, my ball joint was failing, and the mechanic assumed it was the source of the noise.

$300 later, I had a new...
Forum: 4th Generation Maxima (1995-1999)
07-30-2004, 08:26 PM
Replies: 7
Views: 595
Posted By tom_98se

Welcome to the ORG. I would suggest trying to...

Welcome to the ORG. I would suggest trying to search, but it's disabled for non-donating members.

A couple of years ago there was a thread regarding too-light steering. Several people, me...
Forum: 4th Generation Maxima (1995-1999)
07-30-2004, 07:49 PM
Replies: 6
Views: 515
Posted By tom_98se

Mine dropped off as I was driving up a quiet...

Mine dropped off as I was driving up a quiet two-lane street. The metal clanging sound scared the hell out of me, and then I also got a nice metallic thunk as it bounced back into the underside of...
Forum: 4th Generation Maxima (1995-1999)
07-01-2004, 04:25 AM
Replies: 16
Views: 639
Posted By tom_98se

For the right-side control arm, the part # is...

For the right-side control arm, the part # is 54500-41U02. You can verify part numbers @ Nissan4Parts.com (http://www.4nissanparts.com/Content/Main.aspx). The cheapest I found it was $141 plus...
Forum: 4th Generation Maxima (1995-1999)
06-30-2004, 06:13 PM
Replies: 16
Views: 639
Posted By tom_98se

I just went through this with my right-side ball...

I just went through this with my right-side ball joint. In the end, I opted to replace the whole control arm instead of pressing in a new ball joint. There's no option to unbolt the joint on the 4th...
Showing results 1 to 25 of 124
 
Page 1 of 5
1
2
3
Last »


 
Forum Jump


All times are GMT -7. The time now is 04:35 AM.