Maxima Forums

 
Page 1 of 10
1
2
3
Last »
Search: Posts Made By: acercomp71
Showing results 1 to 25 of 250
Search took 0.10 seconds.
Forum: 6th Generation Maxima (2004-2008)
10-19-2015, 03:06 PM
Replies: 4
Views: 7,883
Posted By acercomp71

There is a metal cover covering sensor, that is...

There is a metal cover covering sensor, that is also held by another 10mm screw, that's why a lot of people can't even see the sensor. And yes, crank sensor is located right between engine and...
Forum: 6th Generation Maxima (2004-2008)
06-11-2015, 10:28 PM
Replies: 1
Views: 1,265
Posted By acercomp71

Most likely one of camshaft sensors is bad, which...

Most likely one of camshaft sensors is bad, which is common issue on this car. It recommended that you replace both camshaft sensors even if only one went bad, since besides being stuck on 5th gear,...
Forum: 6th Generation Maxima (2004-2008)
06-10-2015, 10:24 PM
Replies: 16
Views: 18,453
Posted By acercomp71

This make and model requires Matic K transmission...

This make and model requires Matic K transmission fluid. If you or your mechanic thinks otherwise, go ahead and gamble all you want. As it was mentioned in previous post, it's your transmission, do...
Forum: 6th Generation Maxima (2004-2008)
06-10-2015, 08:53 PM
Replies: 4
Views: 809
Posted By acercomp71

Sounds like your little mechanic forgot to put...

Sounds like your little mechanic forgot to put steering pump belt back on. Why don't you go back to him and find out why your steering does not operate properly? And what the hell is "transtune"?
Forum: 6th Generation Maxima (2004-2008)
12-29-2014, 07:17 PM
Replies: 2
Views: 990
Posted By acercomp71

What the hell is VIAS?

What the hell is VIAS?
Forum: 6th Generation Maxima (2004-2008)
12-23-2014, 02:53 PM
Replies: 4
Views: 7,017
Posted By acercomp71

It's a tough call hahahaa! They usually will tell...

It's a tough call hahahaa! They usually will tell you this- hey if you never done any work on cars before, don't touch it! On other hand how can you learn without actually doing it? Go figure! I'd...
Forum: 6th Generation Maxima (2004-2008)
12-23-2014, 02:30 PM
Replies: 8
Views: 1,391
Posted By acercomp71

You got only 2.5 quarts out when draining the...

You got only 2.5 quarts out when draining the fluid? Of course it was too low in first place.
Forum: 6th Generation Maxima (2004-2008)
12-18-2014, 11:05 AM
Replies: 0
Views: 4,568
Posted By acercomp71

Crankshaft Position Sensor SEAL (not o-ring)

Hey all, I just replaced crankshaft sensor and saw a rubber seal, that is shaped like semi circle cylinder. It appears as it functions as additional seal because the hole is not a perfect circle....
Forum: 6th Generation Maxima (2004-2008)
10-06-2014, 12:53 PM
Replies: 11
Views: 1,918
Posted By acercomp71

So who was working on your car and stripped the...

So who was working on your car and stripped the holes? Which dealership is it?
Forum: 6th Generation Maxima (2004-2008)
10-05-2014, 08:45 PM
Replies: 2
Views: 762
Posted By acercomp71

Just buy an aftermarket radio that has aux input...

Just buy an aftermarket radio that has aux input (3.5 mm jack) and install it yourself. You will need several adapters for proper installation, such as hardware adapter, antenna adapter, and wire...
Forum: 6th Generation Maxima (2004-2008)
10-02-2014, 12:52 PM
Replies: 9
Views: 1,182
Posted By acercomp71

Call any Nissan dealer and give them VIN# and ask...

Call any Nissan dealer and give them VIN# and ask for headlight assembly. Take part# down on piece of paper and go from there. You can also buy aftermarket unit, if you want, but exact fitment is not...
Forum: 6th Generation Maxima (2004-2008)
10-02-2014, 12:36 PM
Replies: 11
Views: 1,918
Posted By acercomp71

Maybe they forgot to tighten valve cover bolts or...

Maybe they forgot to tighten valve cover bolts or whatever. It is hard to tell without seeing it, just look carefully where leak originates. Or maybe too much oil in crankcase, builds too much...
Forum: 6th Generation Maxima (2004-2008)
10-02-2014, 12:13 PM
Replies: 11
Views: 1,918
Posted By acercomp71

I've done both valve covers and have no leaks....

I've done both valve covers and have no leaks. Unlike you two, I do my work myself and don't let some idiot mess with it 6 or 9 times and still manage to screw the job. Or seriously, your leak...
Forum: 6th Generation Maxima (2004-2008)
10-01-2014, 06:17 PM
Replies: 10
Views: 13,287
Posted By acercomp71

You have to splice white wire with orange wire...

You have to splice white wire with orange wire professor. Read previous post and follow that link, then thank all of us here who just saved you 200 or 300 bucks whatever that stupid overhead console...
Forum: 6th Generation Maxima (2004-2008)
09-30-2014, 03:03 PM
Replies: 10
Views: 13,287
Posted By acercomp71

There is a way to rewire the assembly so light...

There is a way to rewire the assembly so light stays either on or off, but never auto. The switch itself can not be replaced. You'd need to replace whole assembly, or rewire it. I honestly don't...
Forum: 6th Generation Maxima (2004-2008)
09-06-2014, 08:44 PM
Replies: 10
Views: 1,023
Posted By acercomp71

I've tried every aftermarket rotor from autoparts...

I've tried every aftermarket rotor from autoparts stores out there, and they all eventually warped and gave me vibration. Problem stopped once I switched to EBC slotted and partially drilled, NOT all...
Forum: 6th Generation Maxima (2004-2008)
09-03-2014, 07:34 PM
Replies: 5
Views: 801
Posted By acercomp71

If you are new to car repairs, brake system...

If you are new to car repairs, brake system especially, don't even touch your brakes, leave the job to professional. If things go wrong, you may end up having almost no brakes, or no brakes at all...
Forum: 6th Generation Maxima (2004-2008)
06-21-2014, 12:09 PM
Replies: 4
Views: 633
Posted By acercomp71

The question is ridiculous and is waste of time...

The question is ridiculous and is waste of time for those who read this, and waste of bandwidth too. He gave you correct answer- call Nissan or your favorite aftermarket parts shop and they will tell...
Forum: 6th Generation Maxima (2004-2008)
06-11-2014, 07:23 PM
Replies: 11
Views: 6,232
Posted By acercomp71

Yes, fairly simple job. HIGHLY recommend...

Yes, fairly simple job. HIGHLY recommend replacing both low an high pressure hoses since system is empty already, and it eliminates guesswork where exactly leak originated. Don't forget to properly...
Forum: 6th Generation Maxima (2004-2008)
05-20-2014, 09:16 PM
Replies: 20
Views: 1,545
Posted By acercomp71

Do what you want, it's you car, just keep in mind...

Do what you want, it's you car, just keep in mind that these forums are literally flooded with posts about ruined transmissions. There is always a possibility that you could be next if you continue...
Forum: 6th Generation Maxima (2004-2008)
05-16-2014, 10:22 PM
Replies: 20
Views: 1,545
Posted By acercomp71

Because: 1. any major brand oil filter will...

Because:

1. any major brand oil filter will be as good as OEM most likely, any good filter will do just fine. Same refers to air filter, cabin filter, belts, plugs and other maintenance items....
Forum: 6th Generation Maxima (2004-2008)
05-01-2014, 10:39 AM
Replies: 30
Views: 4,326
Posted By acercomp71

Your list is normal for a car that approaches 10...

Your list is normal for a car that approaches 10 years of age, we have all been there, don't sweat too much. And no, your list is not over. If you still plan to keep the vehicle, you will eventually...
Forum: 6th Generation Maxima (2004-2008)
05-01-2014, 10:26 AM
Replies: 12
Views: 3,049
Posted By acercomp71

Probably problem is at ignition switch. Turn on...

Probably problem is at ignition switch. Turn on and off high beam, if you got power delivered there, but nowhere else, then circuit at ignition switch is stuck open even when you turn your key. Could...
Forum: 6th Generation Maxima (2004-2008)
04-28-2014, 11:47 AM
Replies: 8
Views: 1,433
Posted By acercomp71

Good video.. Now the question is, do you really...

Good video.. Now the question is, do you really need it and is it worth messing with in first place?
Forum: 6th Generation Maxima (2004-2008)
04-24-2014, 09:13 AM
Replies: 15
Views: 1,878
Posted By acercomp71

You've got nothing to twist, these are just...

You've got nothing to twist, these are just push-in pistons as said above. But yea, buy that $7 tool just for kick out of it, just let it sit in your garage silly.
Showing results 1 to 25 of 250
 
Page 1 of 10
1
2
3
Last »


 
Forum Jump


All times are GMT -7. The time now is 06:01 PM.