Search: Posts Made By: Goofball
Showing results 1 to 16 of 16
Search took 0.12 seconds.
05-13-2017, 11:04 AM
Replies: 4
Views: 354
Posted By Goofball

Thanks for the link to the manual. I didn't have...

Thanks for the link to the manual. I didn't have that.
05-13-2017, 11:01 AM
Replies: 4
Views: 354
Posted By Goofball

I understand all that. I was just making the...

I understand all that. I was just making the powers that be know that the links don't work.
05-13-2017, 08:48 AM
Replies: 4
Views: 354
Posted By Goofball

Check engine trouble code links no longer work

I tried using the links to see what my blinks meant, but a Chinese web site is what shows up when the links are clicked.
07-03-2009, 07:23 AM
Replies: 8
Views: 587
Posted By Goofball

Missfire it is. Thanks guys for all your advice.

Missfire it is. Thanks guys for all your advice.
07-02-2009, 01:15 PM
Replies: 8
Views: 587
Posted By Goofball

Which code should I address first? Knock Sensor or Cyl 1 missfire

I have these 2 codes. Which should I fix first? I lost my job after 18 years Tuesday and money is an issue.

thanks
02-03-2009, 06:00 AM
Replies: 14
Views: 739
Posted By Goofball

In the light, I could see I didn't connect...

In the light, I could see I didn't connect something I disconnected. It is fixed.
02-03-2009, 03:57 AM
Replies: 14
Views: 739
Posted By Goofball

I'll do a search for their locations. I had to...

I'll do a search for their locations. I had to walk 20 minutes back to my house. I'll wait til the sun comes up and go back.
02-03-2009, 03:38 AM
Replies: 14
Views: 739
Posted By Goofball

Replaced starter, now engine dies

I replaced my starter last night. My car started fine, but I didn't test drive it. On my way to work this morning, the engine just quit. Luckily I could coast to a side street. The engine restarted...
10-19-2008, 05:49 AM
Replies: 3
Views: 649
Posted By Goofball

I'll get a loaner torque wrench from Autozone to...

I'll get a loaner torque wrench from Autozone to check the tightness. I saw how over tightening reduced how easily the hub turned, so I backed it off a little bit until it turned easier.
10-18-2008, 09:20 AM
Replies: 3
Views: 649
Posted By Goofball

Rear hub nut not very tight

My car was diagnosed with a bad rear hub assembly. I ordered a new one and was installing it this morning. When I put the breaker bar to the nut on the old hub, the nut wasn't hard at all to loosen....
01-16-2007, 06:07 AM
Replies: 0
Views: 512
Posted By Goofball

Can squeaky radiator fans be lubricated?

Both my fans are squeaking. First was my air conditioner fan and now the rad fan also. I took off the air conditioner fan and tightened up all the screws and it helped.

I'm looking for a better...
07-27-2006, 09:21 AM
Replies: 2
Views: 1,137
Posted By Goofball

Mine starts rattling immediately after I turn on...

Mine starts rattling immediately after I turn on the AC. Heads are turning in the parking lot. Not good.
07-27-2006, 08:21 AM
Replies: 2
Views: 1,137
Posted By Goofball

Rattling in secondary radiator fan

When I turn my AC on, the secondary fan by the radiator starts rattling loudly. I haven't taken anything apart for a closer look yet, but was wondering if you guys might suggest what might be causing...
07-18-2006, 04:20 AM
Replies: 8
Views: 4,002
Posted By Goofball

My car won't start if the alarm goes of in my 98...

My car won't start if the alarm goes of in my 98 GLE until I turn the alarm off. Not starting will stop a thief.
03-01-2006, 05:30 AM
Replies: 10
Views: 522
Posted By Goofball

I've tried a couple different brands with no...

I've tried a couple different brands with no success. I'll give the Sonys a try. I've had a few commercial books on CD not work either so I was thinking it was just the radio.
02-28-2006, 12:39 PM
Replies: 10
Views: 522
Posted By Goofball

Mine has trouble sometimes playing CDs to the...

Mine has trouble sometimes playing CDs to the end. Commercial music CDs are fine. If I burn a CD myself, it will play about halfway and then I get the ERR message. Any thoughts?
Showing results 1 to 16 of 16


 
Forum Jump


All times are GMT -7. The time now is 09:12 AM.