Maxima Forums

Search: Posts Made By: Diesel_hunter
Showing results 1 to 24 of 24
Search took 0.01 seconds.
Forum: 5th Generation Maxima (2000-2003)
10-27-2015, 05:22 AM
Replies: 17
Views: 809
Posted By Diesel_hunter

Id say start by replacing the EVAP canister vent...

Id say start by replacing the EVAP canister vent control valve if its cheap or try to home remedy with some cleaning and such
Forum: 5th Generation Maxima (2000-2003)
10-27-2015, 05:04 AM
Replies: 17
Views: 809
Posted By Diesel_hunter

The vent control code is evap, the purge canister...

The vent control code is evap, the purge canister remains open to environment. Under a load this will create a certain form of vacuum "leak" called ported vacuum, i believe this is why you get a VIAS...
Forum: 5th Generation Maxima (2000-2003)
10-27-2015, 04:26 AM
Replies: 45
Views: 6,544
Posted By Diesel_hunter

Also listen for your blend door moving as your...

Also listen for your blend door moving as your cycle thru your hvac options, if you cant hear it thats probably the issue
Forum: 5th Generation Maxima (2000-2003)
10-27-2015, 04:25 AM
Replies: 45
Views: 6,544
Posted By Diesel_hunter

Clogged heater core, faulty thermostat (check...

Clogged heater core, faulty thermostat (check your rad hoses whem warm, a cold one means bad thermo) or crazy as it sounds glycol mixture can affect this pretty harsh, pure coolant wont even get...
Forum: 4th Generation Maxima (1995-1999)
10-27-2015, 04:16 AM
Replies: 24
Views: 5,319
Posted By Diesel_hunter

30 yrs and nvr seen that?! Unbelievable...

30 yrs and nvr seen that?! Unbelievable...
Forum: 4th Generation Maxima (1995-1999)
10-27-2015, 04:13 AM
Replies: 24
Views: 5,319
Posted By Diesel_hunter

WRONG your trans is always moving, nuetral just...

WRONG your trans is always moving, nuetral just means your main shaft isn't in contact with your aux.. one side has to turn with your wheels and one side has to turn with your engine AT ALL TIMES!!...
Forum: 4th Generation Maxima (1995-1999)
10-27-2015, 04:05 AM
Replies: 24
Views: 5,319
Posted By Diesel_hunter

Remove your center caps on your front rims, check...

Remove your center caps on your front rims, check torque on your axle nuts they should 175-215 lb ft if those are kosher i would investigate sway bar links and such... of its only on accel then you...
Forum: 4th Generation Maxima (1995-1999)
10-27-2015, 03:57 AM
Replies: 8
Views: 730
Posted By Diesel_hunter

Throw out bearing or input shaft bearing

Throw out bearing or input shaft bearing
Forum: 4th Generation Maxima (1995-1999)
10-27-2015, 03:55 AM
Replies: 14
Views: 1,264
Posted By Diesel_hunter

When i bought my maxi my speedo didnt work,...

When i bought my maxi my speedo didnt work, replaced the sensor, still nothing. Came to realize that the wire harnesa rides up the front of the trans and i guess it gets real hot in there cause they...
Forum: 4th Generation Maxima (1995-1999)
10-27-2015, 03:49 AM
Replies: 19
Views: 2,026
Posted By Diesel_hunter

Or you could just swap it with another relay that...

Or you could just swap it with another relay that fits and save yourself the bs.. essentially turn your ignition on and work your way back from the solenoid back to the IS, also clean your grounds...
Forum: 4th Generation Maxima (1995-1999)
10-27-2015, 03:40 AM
Replies: 19
Views: 2,026
Posted By Diesel_hunter

Jump the 2 wires on your nuetral saftey switch...

Jump the 2 wires on your nuetral saftey switch together, itll trick the computer into thinkin its safe and itll start assuming that im correct on the switch being faulty
Forum: 4th Generation Maxima (1995-1999)
10-27-2015, 03:33 AM
Replies: 4
Views: 1,076
Posted By Diesel_hunter

Use only lithium grease designed for use with...

Use only lithium grease designed for use with bearings not white grease, i prefer nlgi #2 amsoil (red) it is designed to hold up to heat and pressure, white grease is is for applications where heavy...
Forum: 4th Generation Maxima (1995-1999)
10-27-2015, 03:23 AM
Replies: 11
Views: 3,136
Posted By Diesel_hunter

Please tell me y'all wouldnt re use that line if...

Please tell me y'all wouldnt re use that line if you didnt kink it?? Lol..
Forum: 7th Generation Maxima (2009-2015)
10-27-2015, 03:15 AM
Replies: 30
Views: 88,681
Posted By Diesel_hunter

Yo dude i test drove a 14 maxi a cpl weeks ago,...

Yo dude i test drove a 14 maxi a cpl weeks ago, the cvt is smooth and sorta just "goes with the flow" and dont forget about slappin to sport shift which is always butter smooth with nissan so you get...
Forum: 7th Generation Maxima (2009-2015)
10-27-2015, 03:08 AM
Replies: 30
Views: 88,681
Posted By Diesel_hunter

To me thats just ridiculous... a cylinder cant...

To me thats just ridiculous... a cylinder cant shut down, you can only cut fuel and spark to it which to me just makes less cylinders fight harder to make the same power as more and i dont even wanna...
Forum: 5th Generation Maxima (2000-2003)
10-27-2015, 02:56 AM
Replies: 221
Views: 72,563
Posted By Diesel_hunter

No sense in doing one side for one plug hole, get...

No sense in doing one side for one plug hole, get the upper set and do every gasket from the heads up amd anything else you can get to, i think the set was 60ish when i bought it

Plus have to...
Forum: 4th Generation Maxima (1995-1999)
10-27-2015, 02:17 AM
Replies: 11
Views: 1,077
Posted By Diesel_hunter

Hear yeee! he changed your starter now you have...

Hear yeee! he changed your starter now you have electrical problems?? The answer is quite simple he fried something during the install, and its funny he says the ecu cause thats bout the only thing...
Forum: 4th Generation Maxima (1995-1999)
10-27-2015, 02:00 AM
Replies: 18
Views: 1,521
Posted By Diesel_hunter

If the pedal is limp and gears grind or get stuck...

If the pedal is limp and gears grind or get stuck its a hydro issue no doubt, for being a trans guy he should know all of this lol... my guess he didnt bench bleed the master correctly, also the rod...
Forum: 4th Generation Maxima (1995-1999)
10-27-2015, 01:54 AM
Replies: 18
Views: 1,521
Posted By Diesel_hunter

Also it never hurts to clamp a hose to the...

Also it never hurts to clamp a hose to the bleeder valve, stick it a jug of brake fluid and pump the pedal, keep the res full and eventually you'll push all the air out but never suck any in cause...
Forum: 4th Generation Maxima (1995-1999)
10-27-2015, 01:50 AM
Replies: 18
Views: 1,521
Posted By Diesel_hunter

Yo bro i aint no expert but ive dealt with this...

Yo bro i aint no expert but ive dealt with this SOOO many times on hydro clutches.. 1st bench bleed the master cyl thats crucial, you should barely be able to push the rod by hand with it in a vice.....
Forum: All Motor
10-27-2015, 01:26 AM
Replies: 139
Views: 64,577
Posted By Diesel_hunter

Input shaft bearing and front cover are super...

Input shaft bearing and front cover are super simple sir, remove the front cover bolts and front cover, remove the snap ring holding the IS at the base, then smack that sucker right on the point with...
Forum: 4th Generation Maxima (1995-1999)
10-01-2015, 09:43 AM
Replies: 123
Views: 364,609
Posted By Diesel_hunter

How does the turbo sit so far from the manifolds...

How does the turbo sit so far from the manifolds and still spool hard? And if you somehow swapped your hot and cold side it would be a straight shot to your air/air
Forum: 4th Generation Maxima (1995-1999)
10-01-2015, 08:54 AM
Replies: 13
Views: 2,900
Posted By Diesel_hunter

Did my valve cover gasket, intake gasket, plugs,...

Did my valve cover gasket, intake gasket, plugs, and throttle body gasket all at once, shouldve done the coils too :( but the valve cover set was like 60ish if i remember, but 160 a bank aint bad w/...
Forum: 4th Generation Maxima (1995-1999)
10-01-2015, 07:39 AM
Replies: 7
Views: 8,106
Posted By Diesel_hunter

Engine stall under a load is 9/10 a vacuum leak,...

Engine stall under a load is 9/10 a vacuum leak, listen for a hiss and track it down or sparingly use starting fluid and listen for an idle change to locate, just be careful not to spray it before...
Showing results 1 to 24 of 24


 
Forum Jump


All times are GMT -7. The time now is 06:16 PM.