Maxima Forums

 
Page 1 of 7
1
2
3
Last »
Search: Posts Made By: a33nismo
Showing results 1 to 25 of 152
Search took 0.02 seconds.
Forum: 5th Generation Maxima (2000-2003)
07-26-2013, 08:14 PM
Replies: 20
Views: 3,475
Posted By a33nismo

The IACV motor can also short the ecu. I...

The IACV motor can also short the ecu.

I would remove the ecu and open it up and inspect for damage. If the motor mount or iacv fried the ecu you can normally see it burnt pretty well.

If you...
Forum: 5th Generation Maxima (2000-2003)
07-24-2013, 01:36 PM
Replies: 21
Views: 10,510
Posted By a33nismo

2damax is right in my shop i've seen maybe (3)...

2damax is right in my shop i've seen maybe (3) 5.5gen maxima's come in that needed a head gasket replaced.

It's very rare for that engine so resources are going to be limited.

On a side not...
Forum: 5th Generation Maxima (2000-2003)
07-23-2013, 08:09 PM
Replies: 25
Views: 3,873
Posted By a33nismo

The vibrant one i posted did get rid of all my...

The vibrant one i posted did get rid of all my drone so you shouldn't have any problem.
Forum: 5th Generation Maxima (2000-2003)
07-23-2013, 06:44 PM
Replies: 7
Views: 1,025
Posted By a33nismo

Ebay has buyers protection and should be able to...

Ebay has buyers protection and should be able to help you with your money and if you used paypal then you will definatly get your money back.

Also in the condition area in the item specific almost...
Forum: 5th Generation Maxima (2000-2003)
07-23-2013, 10:32 AM
Replies: 25
Views: 3,873
Posted By a33nismo

Not a problem hopefully it will help someone fix...

Not a problem hopefully it will help someone fix the drone issue they have with the exhaust the 22" magnaflow on there sounds like it would be great. If i hadn't drilled my whole where i did in the...
Forum: 4th Generation Maxima (1995-1999)
07-23-2013, 09:24 AM
Replies: 9
Views: 972
Posted By a33nismo

By any chance do you know where he was taping...

By any chance do you know where he was taping into the oil system to check oil pressure?

Was he removing the oil pressure sensor and using an adaptor and a mechanical oil pressure gauge.
Forum: 5th Generation Maxima (2000-2003)
07-22-2013, 08:02 PM
Replies: 25
Views: 3,873
Posted By a33nismo

The reason i went with the vibrant was because of...

The reason i went with the vibrant was because of the good reviews about it and it really did stop the drone and also because mine is a 2000 fed spec i have a rear O2 sensor that needed to be...
Forum: 4th Generation Maxima (1995-1999)
07-22-2013, 01:33 PM
Replies: 12
Views: 16,708
Posted By a33nismo

What i have done for customers who have done the...

What i have done for customers who have done the work them selfs and that has the same thing happen is use a tiny screw driver or coat hangar and put it in the hole to check the depth of the hole to...
Forum: 5th Generation Maxima (2000-2003)
07-22-2013, 01:05 PM
Replies: 25
Views: 3,873
Posted By a33nismo

I forgot to add I have replaced the factory srs...

I forgot to add I have replaced the factory srs resonator that comes with this exhaust with one from Vibrant. I posted a thread about wanting to replace the factory one on the srs after just a week...
Forum: 5th Generation Maxima (2000-2003)
07-22-2013, 10:52 AM
Replies: 25
Views: 3,873
Posted By a33nismo

Ok here is the updated video of the exhaust i...

Ok here is the updated video of the exhaust i took during lunch after it had warmed up.

2000 nissan maxima srs exhaust warmed up. - YouTube
Forum: 5th Generation Maxima (2000-2003)
07-22-2013, 08:40 AM
Replies: 25
Views: 3,873
Posted By a33nismo

Nope there's no rattle at all. You might be...

Nope there's no rattle at all.

You might be hearing the exhaust popping when i rev it and let off.

This was also a cold start so the exhaust is louder its actually very mellow when warmed up i...
Forum: 5th Generation Maxima (2000-2003)
07-22-2013, 07:32 AM
Replies: 6
Views: 907
Posted By a33nismo

How did the car run prior to getting the timing...

How did the car run prior to getting the timing chain , tensioner and guides installed?

Did you get it replaced due to noise?
Forum: 5th Generation Maxima (2000-2003)
07-22-2013, 07:13 AM
Replies: 25
Views: 3,873
Posted By a33nismo

Yep your correct it has a Warp speed Unequal...

Yep your correct it has a Warp speed Unequal length y-pipe( this is also a fed spec 2000 so no precats at all) along with a new magnaflow catalytic converter. I waited until i had the y-pipe, cat and...
Forum: 5th Generation Maxima (2000-2003)
07-22-2013, 06:48 AM
Replies: 25
Views: 3,873
Posted By a33nismo

Thanks for the replys. This was a cold start...

Thanks for the replys.

This was a cold start so it was idling around 1000 to 1100.

I will take another video after work so you can compare the cold start vs warmed up.
Forum: 5th Generation Maxima (2000-2003)
07-20-2013, 10:42 PM
Replies: 6
Views: 1,052
Posted By a33nismo

Anything is possible but i've yet to see one...

Anything is possible but i've yet to see one done. You would need to do a ton of fab like making the engine and transmission mounts, cutting into the firewall and making the hump for the transmission...
Forum: 5th Generation Maxima (2000-2003)
07-19-2013, 06:18 PM
Replies: 25
Views: 3,873
Posted By a33nismo

My SRS exhaust clip after 1 month of having it on.

So i installed my srs exhaust about a month ago and waited to make sure it was fully broke in before taking a video of it.

The video doesn't capture just how deep it sounds but pretty close.
...
Forum: 5th Generation Maxima (2000-2003)
07-19-2013, 05:56 PM
Replies: 14
Views: 6,038
Posted By a33nismo

find a sport on the belt between two pulleys and...

find a sport on the belt between two pulleys and push down on that section.

How much will it move?

You want it to move a little but no more then 3/8 inch would be ideal.
Forum: 5th Generation Maxima (2000-2003)
07-18-2013, 07:59 PM
Replies: 1,892
Views: 131,487
Posted By a33nismo

My 2000 Maxima has 314,498 miles (went and check...

My 2000 Maxima has 314,498 miles (went and check before i wrote this lol) and still has the stock engine and auto trans. Both engine and trans are strong but swapping a manual trans in it before...
Forum: 5th Generation Maxima (2000-2003)
07-18-2013, 07:29 AM
Replies: 46
Views: 3,835
Posted By a33nismo

Sounds like you might need new outer tie rods if...

Sounds like you might need new outer tie rods if the front end is shaking while driving.

A easy way to test is to jack up the left front tire while the right front in on the ground and grab each...
Forum: 5th Generation Maxima (2000-2003)
07-17-2013, 06:53 AM
Replies: 34
Views: 13,297
Posted By a33nismo

AH i can't comment on good quick struts i've...

AH i can't comment on good quick struts i've never liked the idea of them sorry.

AH i can't comment on good quick struts i've never liked the idea of them and i have heard many horror stories...
Forum: 5th Generation Maxima (2000-2003)
07-16-2013, 09:09 PM
Replies: 34
Views: 13,297
Posted By a33nismo

KYB struts are a very good choice and well...

KYB struts are a very good choice and well recommended on the forum. There valved nicely for the maxima and give sport feel without being harsh.

www.rockauto.com has them for a good price and you...
Forum: 5th Generation Maxima (2000-2003)
07-16-2013, 11:58 AM
Replies: 3
Views: 807
Posted By a33nismo

Just as an update. The bolts that connect...

Just as an update.

The bolts that connect the auto transmission to the engine will also work for the manual transmission along with the bolt that are used to mount the torque converter flexplate...
Forum: 5th Generation Maxima (2000-2003)
07-16-2013, 11:05 AM
Replies: 3,001
Views: 276,926
Posted By a33nismo

Went and picked up some factory side skirts...

Went and picked up some factory side skirts (rocker mouldings) from the junkyard to install of my 00. I just need to sand them down and paint them to match since my color blue was only on 00 and 01...
Forum: 5th Generation Maxima (2000-2003)
07-15-2013, 09:44 PM
Replies: 4
Views: 1,536
Posted By a33nismo

Depending on what ecm it has and also since it...

Depending on what ecm it has and also since it might have been change once before it probably had the ecm updated to the new part # 22680-2y001 maf sensor that replaced the old 22680-ad201 per the...
Forum: 5th Generation Maxima (2000-2003)
07-15-2013, 02:51 PM
Replies: 3
Views: 807
Posted By a33nismo

Yep i have that one and 2 others printed out so i...

Yep i have that one and 2 others printed out so i have plenty of info when i do the swap.

None of them say if they can reuse the bolts so i'm guessing you can. At worst i just go and buy new bolt...
Showing results 1 to 25 of 152
 
Page 1 of 7
1
2
3
Last »


 
Forum Jump


All times are GMT -7. The time now is 02:26 AM.