Maxima Forums

 
Page 1 of 2
1
2
Search: Posts Made By: chiwchan
Showing results 1 to 25 of 33
Search took 0.12 seconds.
Forum: 4th Generation Classifieds (1995-1999)
02-11-2012, 05:05 PM
Replies: 0
Views: 496
Posted By chiwchan

FS: 95-99 Nissan Maxima Ignition Coil LH - $32 shipped

Have one LH ignition coil for sale. Part is like new, only used for testing. Did not need the part since I figured out I had a bad fuel injector. Part was purchased at Autozone - Duralast part...
Forum: 4th Generation Maxima (1995-1999)
01-02-2010, 10:06 PM
Replies: 19
Views: 16,681
Posted By chiwchan

Its the fuel injector, had the same problem -...

Its the fuel injector, had the same problem - replaced fuel injector and everything is fine now...
Forum: 4th Generation Classifieds (1995-1999)
11-09-2008, 10:33 AM
Replies: 0
Views: 271
Posted By chiwchan

FS: 1995 Nissan Maxima - Rear Calipers

Have non-working calipers removed from a 1995 Nissan Maxima.

Both the left and right side.

$20 shipped to you. Otherwise, I will just throw them out.....
Forum: 4th Generation Maxima (1995-1999)
05-07-2006, 04:37 AM
Replies: 3
Views: 750
Posted By chiwchan

Help

Help. Help.
Forum: 4th Generation Maxima (1995-1999)
05-06-2006, 06:09 PM
Replies: 3
Views: 750
Posted By chiwchan

Brake Light Fuse Blown - Short Circuit

Anyone experience a blown fuse for the brake lights? My fuse occasionally blows after I replace it. What's the most likely location of the short or is it the brake sensor going bad? Any...
Forum: 4th Generation Maxima (1995-1999)
09-07-2005, 03:19 PM
Replies: 3
Views: 460
Posted By chiwchan

Catback Exhaust System

What does everyone think about this?

http://cgi.ebay.com/ebaymotors/GREDDY-SP-FULL-EXHAUST-W-REMUS-MUFFLER-95-99-MAXIMA_W0QQitemZ7998120484QQcategoryZ33633QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
...
Forum: 4th Generation Maxima (1995-1999)
08-29-2005, 10:00 PM
Replies: 13
Views: 719
Posted By chiwchan

Is the magnaflow a direct bolt on without any...

Is the magnaflow a direct bolt on without any welding required? Otherwise, what other mufflers are direct bolt ons without modification....
Forum: 4th Generation Maxima (1995-1999)
02-11-2005, 04:32 AM
Replies: 12
Views: 550
Posted By chiwchan

Its the idle air control valve, nneds to be...

Its the idle air control valve, nneds to be cleaned..... I'm sure of this...
Forum: 4th Generation Maxima (1995-1999)
01-05-2005, 04:26 AM
Replies: 7
Views: 505
Posted By chiwchan

Cleaning the idle air control valve will fix...

Cleaning the idle air control valve will fix that. I just did this the other day.
Forum: 4th Generation Maxima (1995-1999)
08-25-2004, 12:50 PM
Replies: 9
Views: 17,657
Posted By chiwchan

I had the 10 08 code on my 1995 Maxima and got...

I had the 10 08 code on my 1995 Maxima and got the $150 part which fixed the problem.
Forum: 4th Generation Maxima (1995-1999)
06-07-2004, 03:44 PM
Replies: 46
Views: 18,497
Posted By chiwchan

Parts I purchased for 10 08 (California...

Parts I purchased for 10 08 (California Emissions):

14920 (Valve)
08911-1081G (Qty=2) - Bolts
14911E (Qty=2) - Clamp
14912MC (Hose)
14912MB (Hose)
Also need new bracket adapter

Call...
Forum: 4th Generation Maxima (1995-1999)
06-04-2004, 08:34 PM
Replies: 46
Views: 18,497
Posted By chiwchan

I purchase from Courtesy Nissan...

I purchase from Courtesy Nissan www.courtesyparts.com , I don't have the part numbers with me, but the part was redesigned, cost about $150 total. Will try to look up parts numbers Monday
Forum: 4th Generation Maxima (1995-1999)
05-03-2004, 01:59 AM
Replies: 24
Views: 2,656
Posted By chiwchan

Maybe you need a new clutch cable?

Maybe you need a new clutch cable?
Forum: 4th Generation Maxima (1995-1999)
12-28-2003, 08:59 PM
Replies: 11
Views: 2,002
Posted By chiwchan

Your struts may be blown. I had the same hopping...

Your struts may be blown. I had the same hopping problem until I replaced my front struts
Forum: 4th Generation Maxima (1995-1999)
12-03-2003, 06:44 PM
Replies: 3
Views: 346
Posted By chiwchan

warped rotors making contact with brake pads most...

warped rotors making contact with brake pads most likely, check your brakes. had the same problem a few months ago.
Forum: 4th Generation Maxima (1995-1999)
11-30-2003, 10:30 AM
Replies: 11
Views: 3,152
Posted By chiwchan

Thats the one. It has two hoses attached to it. ...

Thats the one. It has two hoses attached to it. If you open up the part, the contacts are probably all corroded inside. I had a hard time replacing the part since the dealer I ordered from sent me...
Forum: 4th Generation Maxima (1995-1999)
11-29-2003, 07:03 PM
Replies: 11
Views: 3,152
Posted By chiwchan

The 1008 code will come back shortly. I replaced...

The 1008 code will come back shortly. I replaced my valve which corrected the problem. It cost me about $150 for the valve, bracket, and two hoses. Nissan redesigned this valve since it was a...
Forum: 4th Generation Maxima (1995-1999)
11-24-2003, 03:23 PM
Replies: 46
Views: 18,497
Posted By chiwchan

Alos, opened up the old damaged valve and the...

Alos, opened up the old damaged valve and the contacts were all corroded.
Forum: 4th Generation Maxima (1995-1999)
11-24-2003, 03:22 PM
Replies: 46
Views: 18,497
Posted By chiwchan

I got code 10 08 and finally fixed it. Replaced...

I got code 10 08 and finally fixed it. Replaced the valve, make sure you order the correct part.Cost me about $140 to replace valve and mini hoses and bracket.
Forum: 4th Generation Maxima (1995-1999)
11-13-2003, 05:31 PM
Replies: 8
Views: 575
Posted By chiwchan

Same problem here. Happened today at like 5:40 PM...

Same problem here. Happened today at like 5:40 PM in Jersey when I left work. After starting, pressed gas pedal to rev engine slightly to keep from stalling then everything was okay. Only happens...
Forum: 4th Generation Maxima (1995-1999)
10-19-2003, 10:20 AM
Replies: 7
Views: 608
Posted By chiwchan

I think I finally fixed the 10 08 code. I have a...

I think I finally fixed the 10 08 code. I have a 1995 Nissan Maxima and the replacement EVAP Canister Purge Control Valve was redesigned. I contacted one Nissan Dealer and they had no idea, so I...
Forum: 4th Generation Maxima (1995-1999)
10-13-2003, 04:20 PM
Replies: 7
Views: 608
Posted By chiwchan

According to Chilton , this is the EVAP Canister...

According to Chilton , this is the EVAP Canister purge control valve, not the solenoid (Code 08 07) as mentioned above and in the FAQ. Is this why we all are unable to get rid of the 10 08 code?...
Forum: 4th Generation Maxima (1995-1999)
10-11-2003, 08:02 AM
Replies: 7
Views: 608
Posted By chiwchan

Just took a look again, there are two solenoid...

Just took a look again, there are two solenoid valves that are alike in that area. Is it the black or green solenoid valve? The part numbers are just about identical with one number different (last...
Forum: 4th Generation Maxima (1995-1999)
10-08-2003, 05:32 PM
Replies: 7
Views: 470
Posted By chiwchan

purge control valve?

purge control valve?
Forum: 4th Generation Maxima (1995-1999)
10-06-2003, 02:17 PM
Replies: 7
Views: 608
Posted By chiwchan

did all that, replaced my valve and reset code...

did all that, replaced my valve and reset code and still getting the code
Showing results 1 to 25 of 33
 
Page 1 of 2
1
2


 
Forum Jump


All times are GMT -7. The time now is 10:40 PM.