Injectors 1,3,5 have no power
#1
Injectors 1,3,5 have no power
I have recently found out that injectors 1,3,5 are not getting any power. I check the harness and it check out good, I even flipped the entire inector rail and used the 2,4,6 harness to make sure the injectors where not bad and they work pefectly. I need to know what are the chances of the ECU being bad and how to go about troubleshooting the issue.
#4
Well, it's worth a shot, but try getting the 135 harness from a junk yard. You could just splice in the new harness without having to removing much, and if it sprays, then that was your problem.
#5
#7
check the ecu codes?
http://forums.nicoclub.com/zerothread?id=126534
you sound like you know what the hell you're doing.. so I cant be much help, other than that list of codes the ecu can throw out.
http://forums.nicoclub.com/zerothread?id=126534
you sound like you know what the hell you're doing.. so I cant be much help, other than that list of codes the ecu can throw out.
#9
Dhunterx, I'm only getting power to 2,4,6. To run a test on the injectors 1,3,5 I simply hook the 2,4,6 harness to see if they would fire and they did. This let me know there was no power getting to injectors 1,3,5. I also check the wire harness for 1,3,5 that plugs to main harness and the continuity was good from end to end.
#10
I have recently found out that injectors 1,3,5 are not getting any power. I check the harness and it check out good, I even flipped the entire inector rail and used the 2,4,6 harness to make sure the injectors where not bad and they work pefectly. I need to know what are the chances of the ECU being bad and how to go about troubleshooting the issue.
#11
are you simply not getting a positive to each, or are you not getting a reading off of both pins? what I mean is, I believe that all 6 get positive power all the time, and are triggered by the ecu completing the circuit by grounding them.
this could be wrong, but I am too tired to search.
this could be wrong, but I am too tired to search.
#13
Have you checked the injector grounds for the rear bank? Is the ECU providing power at the ecu for the injectors? Is this a VG or VE? If its a VG check your distributor optical timing wheel maybe 1,3,5 have something blocking it? Swap out you knock sensor with another! Use a noid tester.... on those injector plugs
#14
After doing some checks I found that I have power at injectors 1,3,5 when I have the ignition switch on. When I grounded my test light I heard the injector fire which tells me there is a problem with the ground. So if this is the case is there a possibility that the ECU is not providing the ground to close the circuit? I also have continuity from each connector back to the battery with the positive lead to the battery unhooked.
Last edited by Amillyon; 07-24-2008 at 07:11 PM.
#19
Here's the update, I swapped out the ECU and still no luck to injectors 1, 3, 5. I'm about to pull my hair out on this one, I have a red/blue, red/yellow and red/black with a peppermint colored wire going into another harness (the main harness). This is connected to green/spotted silver, a green/brown with spotted silver and one brown wire that go back to the ECM. The continuity from the ECM connector to each wire is good (a few inches past the connector). I did get a high reading on the spotted silver between the connector that plugs into the injector harness and the other side right before it goes in the car. With the ignition on and each injector unplug I get power to each wire except 3 and 5. I get power to 3 and 5 only when 1,3,5 are connected. If anyone can make sense of this please post.
Last edited by Amillyon; 07-25-2008 at 02:22 PM.
#20
Ok, my ECU is throwing a code 34 Knock sensor would this keep injectors 1,3,5 from spraying? If anyone sees raeqwon28 online please tell him I'm having the same issue he was having in this post >>>> http://forums.maxima.org/3rd-generat...e-harness.html I'm sure he could tell me what the problem is!!
Last edited by Amillyon; 07-25-2008 at 09:18 PM.
#21
sounds about right! There jobs is to retard timing or cut down cylinders when detonation is sensed, try to unplug it replace it and try to start it! Knock sensors can do some weird things!
#22
#24
#25
Capedcadaver, we've spoken before a few months back I'm in Durham,NC. To give you a run down of what happened. I have injectors 1,3, and 5 not spraying, so far I have swapped the ECU and the injectors ohm out at 11.5. I have power to all the injectors when the connectors are on each injector. If I disconnect all of the connections from each injector I have power at all except 3,5. I only get power to 3 and 5 when 1 is connected to the injector along with 3 and5. If I ground the 1,3,5 injectors with my test light then I hair each one spray. The continuity was good from the ECU/SMJ connector to a inches passed it on the brown/spotted silver, green/spotted silver and Green/black striped wire. What could be keeping my injectors from spraying?
Last edited by Amillyon; 07-26-2008 at 06:36 PM.
#27
Capedcadaver, we've spoken before a few months back I'm in Durham,NC. To give you a run down of what happened. I have injectors 1,3, and 5 not spraying, so far I have swapped the ECU and the injectors ohm out at 11.5. I have power to all the injectors when the connectors are on each injector. If I disconnect all of the connections from each injector I have power at all except 3,5. I only get power to 3 and 5 when 1 is connected to the injector along with 3 and5. If I ground the 1,3,5 injectors with my test light then I hair each one spray. The continuity was good from the ECU/SMJ connector to a inches passed it on the brown/spotted silver, green/spotted silver and Green/black striped wire. What could be keeping my injectors from spraying?
i apologize for not remembering you either... there's a lot of members and it's hard to remember who's where. i just put my location under my avatar so it's easy to see at a glance. anyhow are you a VE or a VG?
#29
#30
Ok, I thought so. I tried to use the old thread command in the link but still nothing. Just to let everyone know I recently put a tranny in this car. I saw a thread where someone else was having the same problem with injectors 1,3,5 not working on an 89SE. The question that was asked was :
"Be sure you don't have the wiring harness for the front injectors flipped around with the wiring harness for the nuetral/reverse sensor coming from the tranny. Yes they fit in each other, yes it cuts out the front 3 cylinders, yes I've done it.
For all three to be out that'd be one of my guesses if you ever unhooked those wires. They're easy to flip around if you don't know the wires too well." mtcookson
Could this happen on a 94 GXE being that I just put a tranny in?
"Be sure you don't have the wiring harness for the front injectors flipped around with the wiring harness for the nuetral/reverse sensor coming from the tranny. Yes they fit in each other, yes it cuts out the front 3 cylinders, yes I've done it.
For all three to be out that'd be one of my guesses if you ever unhooked those wires. They're easy to flip around if you don't know the wires too well." mtcookson
Could this happen on a 94 GXE being that I just put a tranny in?
#31
Ok, I thought so. I tried to use the old thread command in the link but still nothing. Just to let everyone know I recently put a tranny in this car. I saw a thread where someone else was having the same problem with injectors 1,3,5 not working on an 89SE. The question that was asked was :
"Be sure you don't have the wiring harness for the front injectors flipped around with the wiring harness for the nuetral/reverse sensor coming from the tranny. Yes they fit in each other, yes it cuts out the front 3 cylinders, yes I've done it.
For all three to be out that'd be one of my guesses if you ever unhooked those wires. They're easy to flip around if you don't know the wires too well." mtcookson
Could this happen on a 94 GXE being that I just put a tranny in?
"Be sure you don't have the wiring harness for the front injectors flipped around with the wiring harness for the nuetral/reverse sensor coming from the tranny. Yes they fit in each other, yes it cuts out the front 3 cylinders, yes I've done it.
For all three to be out that'd be one of my guesses if you ever unhooked those wires. They're easy to flip around if you don't know the wires too well." mtcookson
Could this happen on a 94 GXE being that I just put a tranny in?
http://forums.maxima.org/3rd-generat...hats-next.html read that entire thread
Last edited by CapedCadaver; 07-27-2008 at 03:49 PM.
#32
++++++++++
Firewall
+++++++++++++
246
135 <-------- Not working (connected to a sub harness) Wire Red/black Red Yellow, Red/Blue
+++++++++++++
Front of the car
++++++++++++
Firewall
+++++++++++++
246
135 <-------- Not working (connected to a sub harness) Wire Red/black Red Yellow, Red/Blue
+++++++++++++
Front of the car
++++++++++++
Last edited by Amillyon; 07-27-2008 at 04:01 PM.
#33
i thought you were talking about the rears the whole time.
http://i164.photobucket.com/albums/u...t/IMG_1631.jpg see the #s on the wires? ignore the turbo that i used as a photo-op/joke
Last edited by CapedCadaver; 07-27-2008 at 04:08 PM.
#34
I'm at work at the moment, so standing in front of the car the closest three cylinders are 2,4,6 ? Another thing is that the harness that is attach to the those injectors have 4 wires, One red/white wire that they all share and then Red/black, Red Yellow, Red/Blue which is now plugged into a connector that only has three wires Brown, green and green/black..... something isn't connected. That post you sent me makes me think I have something hooked up wrong for sure.
#35
I'm at work at the moment, so standing in front of the car the closest three cylinders are 2,4,6 ? Another thing is that the harness that is attach to the those injectors have 4 wires, One red/white wire that they all share and then Red/black, Red Yellow, Red/Blue which is now plugged into a connector that only has three wires Brown, green and green/black..... something isn't connected. That post you sent me makes me think I have something hooked up wrong for sure.
#36
I'm very relieved to know exactly what the problem was. My tranny inhibitor wires are attached to my front row of injectors WOW!! The connectors are the same shape and it's very easy to get them mixed up if you don't pay attention. I would like to thank everyone who gave their input and stuck it out to the end. Capedcadaver I'm right here in Durham if ever need some help just hit me up. I have a boat load of tools and don't mind getting my hands dirty. If you have an instant messenger ID send me a private message, everyone thanks again!
#37
I'm very relieved to know exactly what the problem was. My tranny inhibitor wires are attached to my front row of injectors WOW!! The connectors are the same shape and it's very easy to get them mixed up if you don't pay attention. I would like to thank everyone who gave their input and stuck it out to the end. Capedcadaver I'm right here in Durham if ever need some help just hit me up. I have a boat load of tools and don't mind getting my hands dirty. If you have an instant messenger ID send me a private message, everyone thanks again!
did you swap them and now it runs right?
#38
Well capedcadaver I'm at work here in Cary at the moment, so I'll have to swap them when I get home tonight. Yes, I have a two ton shop jack and some heavy duty jack stands I got from Harbor Frieght tools.
#39
ugh i used to work in cary at this thinly-disguised door-to-door marketing (not sales, because we were soliciting free estimates). worst job ever. i quit it a week before i started my 5spd swap. anyhow maybe tomorrow or something we can do that. i wouldn't want to make you drive from cary all the hell back to durham, and THEN back out here to freaking east raleigh (that'd be like 70 miles of driving by the time you got home) so late at night and all.
Thread
Thread Starter
Forum
Replies
Last Post
jmlee44
4th Generation Maxima (1995-1999)
8
10-02-2022 02:13 PM