Maxima Forums

Search: Posts Made By: 10's or bust
Showing results 1 to 14 of 14
Search took 0.04 seconds.
Forum: 3rd Generation Maxima (1989-1994)
12-19-2009, 12:39 AM
Replies: 33
Views: 5,024
Posted By 10's or bust

Its not about the Mass Air Flow Sensor knowing...

Its not about the Mass Air Flow Sensor knowing the size of the injectors but rather simply the capacity or volume of air that sensor is physically cable of reading or reporting back to the ECU in...
Forum: 3rd Generation Maxima (1989-1994)
12-19-2009, 12:26 AM
Replies: 33
Views: 5,024
Posted By 10's or bust

really then why do we have stand alone units tha...

really then why do we have stand alone units tha do just that but way better than the factory electronics could have done?
Forum: 3rd Generation Maxima (1989-1994)
12-19-2009, 12:19 AM
Replies: 56
Views: 2,456
Posted By 10's or bust

he's looking to rebuild especially if it was...

he's looking to rebuild especially if it was leaking gea oil. I bet those sychos are toast. about 700 dollars if he can find a good builder
Forum: 5th Generation Maxima (2000-2003)
12-16-2009, 06:57 PM
Replies: 85
Views: 14,110
Posted By 10's or bust

just get the JDM tranny, and get an oversized...

just get the JDM tranny, and get an oversized transcooler and dont even bother with cooler in the radiator as all FWD Borg Warner trannies that nissan use suffer from the effects of low lube flow and...
Forum: 5th Generation Maxima (2000-2003)
12-16-2009, 06:46 PM
Replies: 85
Views: 14,110
Posted By 10's or bust

I've built a few of these trannies and I can tell...

I've built a few of these trannies and I can tell u to build them and build them right everything inside must be replaced and nothing reused at all. Assuming the builder buys everthying new the price...
Forum: 5th Generation Maxima (2000-2003)
12-16-2009, 06:34 PM
Replies: 85
Views: 14,110
Posted By 10's or bust

if done properly a rebuild will always outlast...

if done properly a rebuild will always outlast the original counterpart but that's only if the build is giong to replace everything and reuse nothing other than the case, valvebody, and front...
Forum: 3rd Generation Maxima (1989-1994)
12-16-2009, 02:09 AM
Replies: 49
Views: 9,196
Posted By 10's or bust

i believe the egr delete is giving u the problems...

i believe the egr delete is giving u the problems u r experiencing check to make certain its not leaking there and since u do have a cali model u may hve to switch out the Ecu witha fed emission on...
Forum: 3rd Generation Maxima (1989-1994)
12-15-2009, 11:28 PM
Replies: 59
Views: 20,366
Posted By 10's or bust

y when u can just by the damned camaro and...

y when u can just by the damned camaro and lighten it!!!!!If u wanted the camaro why not just by the camaro in the first place!!!! The z31 powerplant is far more advanced all over especailly in terms...
Forum: 3rd Generation Maxima (1989-1994)
12-15-2009, 11:21 PM
Replies: 59
Views: 20,366
Posted By 10's or bust

thats the swap i'm considering!!!!If they can...

thats the swap i'm considering!!!!If they can make FWD Eclipses AWD just from the rear subframe assy, fuel tank, and awd tranny and driveshaft the certainly its possible to make the maxima AWD!!! But...
Forum: 3rd Generation Maxima (1989-1994)
12-15-2009, 11:15 PM
Replies: 59
Views: 20,366
Posted By 10's or bust

why not just get the clip from jdm pulsar gti-r...

why not just get the clip from jdm pulsar gti-r and subframe and then u have the best of all worlds killer horsepower and awd yes the trans are the same all the way to the internal gearing
Forum: 3rd Generation Maxima (1989-1994)
12-15-2009, 10:51 PM
Replies: 29
Views: 2,764
Posted By 10's or bust

Check the torque of the crank bolt to be sure its...

Check the torque of the crank bolt to be sure its still tight b/c if it comes the so will ur belt and bent valves will definately be the end result so make sure the crank bolt and pulleys r...
Forum: 3rd Generation Maxima (1989-1994)
12-15-2009, 10:08 PM
Replies: 7,152
Views: 541,286
Posted By 10's or bust

take the time to wiggle all plugs going to the...

take the time to wiggle all plugs going to the transmissiion especially the ones going to the inhibitor(neutral-safety switch) check out the inhibitor relay as well by swapping it out with a known...
Forum: 3rd Generation Maxima (1989-1994)
12-15-2009, 09:47 PM
Replies: 33
Views: 5,024
Posted By 10's or bust

having personal rewired this plug on my 91 Se i...

having personal rewired this plug on my 91 Se i simply tapped in to the ground running the sensor and tied it to the ground running to the ignition and the response was nothing short of amazing by...
Forum: General Maxima Discussion
08-12-2009, 02:24 AM
Replies: 14
Views: 776
Posted By 10's or bust

Fast

140+ plus dont ask!!!! 176MPH to be exact!!!! no longer have that tranny anymore....so i guess it doesn't matter
Showing results 1 to 14 of 14


 
Forum Jump


All times are GMT -7. The time now is 02:42 PM.