Maxima Forums

 
Page 1 of 19
1
2
3
11
Last »
Search: Posts Made By: SamMan23
Showing results 1 to 25 of 454
Search took 0.24 seconds.
Forum: 4th Generation Maxima (1995-1999)
07-18-2012, 08:29 PM
Replies: 6
Views: 1,151
Posted By SamMan23

turned out to be the MAF. no codes. It would...

turned out to be the MAF. no codes. It would only do it at operating temperature when it was hot. new MAF = no problem.
Forum: 4th Generation Maxima (1995-1999)
06-22-2012, 07:04 PM
Replies: 6
Views: 1,151
Posted By SamMan23

Thanks bro. I'll spray down that MAF wire...

Thanks bro. I'll spray down that MAF wire tomorrow. Then clean the TB. Hopefully that will get it up and running again.
Forum: 4th Generation Maxima (1995-1999)
06-19-2012, 05:26 PM
Replies: 6
Views: 1,151
Posted By SamMan23

it has been over 100k since a tb clean. might be...

it has been over 100k since a tb clean. might be time.
Forum: 4th Generation Maxima (1995-1999)
06-17-2012, 06:05 PM
Replies: 6
Views: 1,151
Posted By SamMan23

Hesitation and Stalling

The vehicle stalls when at low speeds and hesitates at low rpms. If the rpms are in the 1000-1500 range it may either stall or if I give it a little gas it may hesitate for a second while I'm on the...
Forum: General Maxima Discussion
01-05-2012, 04:38 PM
Replies: 2
Views: 666
Posted By SamMan23

What alternator should I get and write-up

What alternators have you guys had good experiences with and which ones were bad? I have had bad experiences with alternators from autozone. Advance carries Remy, Denso, Worldwide, and Beck Arnley....
Forum: 4th Generation Maxima (1995-1999)
07-11-2010, 07:38 PM
Replies: 19
Views: 4,051
Posted By SamMan23

do you mean regarding power?

do you mean regarding power?
Forum: 4th Generation Maxima (1995-1999)
07-10-2010, 02:41 PM
Replies: 19
Views: 4,051
Posted By SamMan23

Ethanol mixed gas - Still usinge 91 octane or better?

I used to buy 93 octane instead of 87 because I got my money back through gas mileage. Now that we have this ethanol mixed into our gas, the gas mileage has gone down as if I was using 87. I don't...
Forum: Garage and Workshop
06-12-2008, 08:08 PM
Replies: 12
Views: 2,018
Posted By SamMan23

I want to get a 42" box. I have a 26" craftman...

I want to get a 42" box. I have a 26" craftman plus a stack on top of that.
Forum: Garage and Workshop
06-12-2008, 10:36 AM
Replies: 12
Views: 2,018
Posted By SamMan23

Want to buy a tool box

Any recommendations? I don't want to pay Snap-on or Matco for their boxes. I would however consider paying Craftsman or Harbor Freight Tools for their boxes. They can be ball bearing or not.
Forum: Garage and Workshop
06-12-2008, 10:33 AM
Replies: 71
Views: 5,601
Posted By SamMan23

I work for a HVAC company and most dealership...

I work for a HVAC company and most dealership garages are fitted with gas fired tubular radiant style heaters suspended from the ceiling.

After talking to a vender who sells the product, this...
Forum: 4th Generation Maxima (1995-1999)
06-08-2008, 03:06 PM
Replies: 3
Views: 741
Posted By SamMan23

Jacking Heights required. Harbor Freight racing ok?

What floor jack height ranges are good for our cars?

Has anyone owned the harbor freight racing jack(non rapid pump)? any complaints about them?

3000 lbs
3" to 14.25" range.
Forum: 4th Generation Maxima (1995-1999)
02-08-2008, 03:15 PM
Replies: 10
Views: 1,541
Posted By SamMan23

It could be your wheel bearings.

It could be your wheel bearings.
Forum: 4th Generation Maxima (1995-1999)
12-06-2007, 08:04 AM
Replies: 37
Views: 1,548
Posted By SamMan23

Honda starters have always been a little high...

Honda starters have always been a little high pitched from the factory. Nissan sounds different. I think that when it comes to alternators and starters you are better off with factory or NAPA.
Forum: 4th Generation Maxima (1995-1999)
12-04-2007, 01:39 PM
Replies: 25
Views: 887
Posted By SamMan23

clean it all up and then change out the valve...

clean it all up and then change out the valve cover. The reason why it's all grimy is because it is leaking.
Forum: 4th Generation Maxima (1995-1999)
09-14-2007, 01:56 PM
Replies: 2
Views: 389
Posted By SamMan23

The VQ engines has coil packs which utilizes a...

The VQ engines has coil packs which utilizes a computer to time the ignition. All you have to do is replace the plug. The elimination of the coil packs eliminate traditional plug wires also.
Forum: 4th Generation Maxima (1995-1999)
07-17-2007, 01:17 PM
Replies: 19
Views: 749
Posted By SamMan23

I believe that one side requires a slide hammer...

I believe that one side requires a slide hammer and the other requires unbolting.

I've replace both sides. I don't remember which side is which. One time when I was pulling the sides with...
Forum: 4th Generation Maxima (1995-1999)
10-24-2006, 02:44 PM
Replies: 5
Views: 666
Posted By SamMan23

the AGX strut had compressed and would not...

the AGX strut had compressed and would not unbind. That's why the strut mount broke. Has this happened to anybody else before? Has anyone worked with KYB on warranty replacements?
Forum: 4th Generation Maxima (1995-1999)
10-20-2006, 12:50 PM
Replies: 5
Views: 666
Posted By SamMan23

the rear aftermarket mount broke. I don't...

the rear aftermarket mount broke. I don't remember the company. It gave it a little bit more travel. I can't believe it. Now I have to go buy some oem mount plates.
Forum: 4th Generation Maxima (1995-1999)
10-20-2006, 11:46 AM
Replies: 5
Views: 666
Posted By SamMan23

right rear clunking over speed bumps and pot holes

I seem to be getting clunking as I drive over speed bumps and pot holes. Anybody have this problem? How do you fix it?

i've got H&R springs, aftermarket spring seat with kyb agx.
Forum: Tires and Wheels
03-31-2006, 04:59 AM
Replies: 5
Views: 622
Posted By SamMan23

no issues with hubcentricity? correct offset? ...

no issues with hubcentricity? correct offset? smooth ride?
Forum: Tires and Wheels
03-29-2006, 07:13 PM
Replies: 5
Views: 622
Posted By SamMan23

1997 240sx wheels on 98 Max

will they fit right? I don't know what offset and bolt patterns are on the 240sx and if they have different sizes on front and back.
Forum: Tires and Wheels
03-07-2006, 02:02 PM
Replies: 1
Views: 470
Posted By SamMan23

toyota rims fit

I'm considering putting the wheels from the Scion tC on my 98 GXE. Would there be any hubcentricity issues? I don't want to spend all that money to get vibrations in my car. I think they'd look...
Forum: Tires and Wheels
03-07-2006, 01:54 PM
Replies: 165
Views: 23,335
Posted By SamMan23

I've got them in 215/60/15. They sucked from day...

I've got them in 215/60/15. They sucked from day 1. always had a vibration till now that they're almost worn out. Now wet traction sucks at highway speeds. i've spent lots of time getting them...
Forum: 4th Generation Maxima (1995-1999)
11-27-2005, 09:12 PM
Replies: 13
Views: 3,901
Posted By SamMan23

I've used the Uhaul one. pulled 2000 lbs for for...

I've used the Uhaul one. pulled 2000 lbs for for 250 miles. works good. but I'd recommend hidden hitch if I was to do it over again...
Forum: 4th Generation Maxima (1995-1999)
11-15-2005, 10:01 AM
Replies: 14
Views: 984
Posted By SamMan23

okay, I got the bolt loose. I just had to put...

okay, I got the bolt loose. I just had to put some muscle into it. I was afraid of breaking something before, but not I realize that it's okay to put some muscle in. used the breaker bar and it came...
Showing results 1 to 25 of 454
 
Page 1 of 19
1
2
3
11
Last »


 
Forum Jump


All times are GMT -7. The time now is 06:10 PM.