Maxima Forums

 
Page 1 of 4
1
2
3
Last »
Search: Posts Made By: mmgio
Showing results 1 to 25 of 79
Search took 0.10 seconds.
Forum: 4th Generation Maxima (1995-1999)
05-13-2014, 02:31 PM
Replies: 2
Views: 473
Posted By mmgio

thanks for the heads up nealoc. Left him a pm.

thanks for the heads up nealoc. Left him a pm.
Forum: 4th Generation Maxima (1995-1999)
05-09-2014, 04:56 PM
Replies: 2
Views: 473
Posted By mmgio

need 5 speed transmission rebuild? (dgeesman?)

My input shaft bearing is going bad on my 1998 maxima.I am in pa and There is a guy in Harrisburg pa that does them? Dgeesman? I am trying to get a hold of him to talk about it by phone. Any help...
Forum: 4th Generation Maxima (1995-1999)
01-31-2014, 04:33 PM
Replies: 1
Views: 672
Posted By mmgio

There is no relearn procedure for our cars. Did...

There is no relearn procedure for our cars. Did you turn the phillips screw on top of the iac in? Screw it in for lower idle. If it is all the way in I would make sure you don't have a vacuum leak....
Forum: 4th Generation Maxima (1995-1999)
01-13-2014, 02:51 PM
Replies: 42
Views: 2,379
Posted By mmgio

Did you remove the ball joint cotter pin and...

Did you remove the ball joint cotter pin and retighten those as you can't get a torque wrench on there. That is exactly what my car did when I left the ball joint nut was too loose. I would also...
Forum: 4th Generation Maxima (1995-1999)
01-11-2014, 04:54 PM
Replies: 5
Views: 608
Posted By mmgio

very well could be the master cyl. The leak will...

very well could be the master cyl. The leak will be inside the car where the master cyl. comes through the firewall. Feel the area for any wet spots (under the dash). If none Check where the hose...
Forum: 4th Generation Maxima (1995-1999)
12-24-2013, 08:50 PM
Replies: 42
Views: 2,379
Posted By mmgio

did you torque everything down with the...

did you torque everything down with the suspension loaded? Make sure your ball joint nut is tight. If loose it will do as you described. Also may be a strut mount.Did you replace them when you did...
Forum: 4th Generation Maxima (1995-1999)
11-21-2013, 04:00 PM
Replies: 13
Views: 1,357
Posted By mmgio

The new clutch and flywheel have been installed...

The new clutch and flywheel have been installed and the clutch feels fine. There is an issue tho when at idle the car vibrates.The tach does not fluctuate at all and the idle is not set low but I...
Forum: 4th Generation Maxima (1995-1999)
11-17-2013, 09:05 AM
Replies: 13
Views: 1,357
Posted By mmgio

S1cTech, Thanks for the tips on the 5th gen...

S1cTech, Thanks for the tips on the 5th gen clutch and harder release. I did order the exedy 06044 clutch kit for $120. I had the mechanic get me a new flywheel from napa. I agree with IslandMax that...
Forum: 4th Generation Maxima (1995-1999)
11-13-2013, 05:06 PM
Replies: 13
Views: 1,357
Posted By mmgio

I took IslandMax's advice and ordered the exedy...

I took IslandMax's advice and ordered the exedy clutch for $120.As for the flywheel I want to get a new one because he said he would have to mail it off to get it machined and I don't have the time...
Forum: 4th Generation Maxima (1995-1999)
11-13-2013, 03:17 PM
Replies: 13
Views: 1,357
Posted By mmgio

Thanks for the replies. I can get the exedy...

Thanks for the replies. I can get the exedy clutch kit for $120 vs 300 for nissan. I was under the impression that the exedy 06044 was the same as the oem with out the dealer mark up.Can anyone shed...
Forum: 4th Generation Maxima (1995-1999)
11-12-2013, 05:11 PM
Replies: 13
Views: 1,357
Posted By mmgio

I appreciate the tip as I have heard this before....

I appreciate the tip as I have heard this before. Thanks again
Forum: 4th Generation Maxima (1995-1999)
11-12-2013, 05:00 PM
Replies: 13
Views: 1,357
Posted By mmgio

need clutch for 1998 five speed.(Update) with another question

My clutch gave out and i'm looking for a new one. I am looking for a stock set up because I don't beat the car.I've been doing a lot of searching and I think i'm going to go with the exedy clutch...
Forum: 4th Generation Maxima (1995-1999)
07-22-2013, 03:42 PM
Replies: 21
Views: 2,385
Posted By mmgio

Why do you guys think it's not the iac valve?...

Why do you guys think it's not the iac valve? That's what the code said. If it was my car I would clean the iac valve and see if it fixes the problem.If it does not I would replace the iac valve....
Forum: 4th Generation Maxima (1995-1999)
04-23-2013, 03:46 PM
Replies: 20
Views: 1,722
Posted By mmgio

I would check the ball joint nut with a torque...

I would check the ball joint nut with a torque wrench with a jack under the control arm. Might also wanna check your wheel bearing for play Push the wheel in and out with the tire on. It shouldn't...
Forum: 4th Generation Maxima (1995-1999)
03-27-2013, 03:45 PM
Replies: 20
Views: 2,193
Posted By mmgio

Did you torque all the bolts with the weight of...

Did you torque all the bolts with the weight of the vehicle on the wheels with a torque wrench? If not that is another thing you should do even if this doesn't fix your problem. I put jack stands...
Forum: 4th Generation Maxima (1995-1999)
03-27-2013, 03:37 PM
Replies: 20
Views: 2,193
Posted By mmgio

I would check your axles make sure they are fully...

I would check your axles make sure they are fully seated in the tranny and hub. They may have also be separated at the joints. I think it has to be one of the things I mentioned.
Forum: 4th Generation Maxima (1995-1999)
03-06-2013, 05:31 PM
Replies: 5
Views: 861
Posted By mmgio

You may as well get the inner and outer tie rods...

You may as well get the inner and outer tie rods if they haven't been replaced because you will need and alignment when you are done.Inner tie rods are tough to do with out the tie rod removal tool....
Forum: 4th Generation Maxima (1995-1999)
12-02-2012, 10:22 AM
Replies: 7
Views: 1,069
Posted By mmgio

have you ever cleaned your IAC valve? I would...

have you ever cleaned your IAC valve? I would also clean the throttle body.
Forum: 4th Generation Maxima (1995-1999)
08-20-2012, 05:29 PM
Replies: 14
Views: 1,006
Posted By mmgio

I got a screwdriver and wedged the throttle open...

I got a screwdriver and wedged the throttle open near the cables and spray carb cleaner in the throttle body opening.Then i take a microfiber towel and push it as far as I can in to the throttle body...
Forum: 4th Generation Maxima (1995-1999)
08-17-2012, 06:59 PM
Replies: 14
Views: 1,006
Posted By mmgio

I have a 5 speed and mine does not do that.Did...

I have a 5 speed and mine does not do that.Did any of you clean your throttle body? When mine gets dirty it will do that.Then I clean the throttle body and the rpms never drop below idle speed.
Forum: 4th Generation Maxima (1995-1999)
07-23-2012, 04:27 PM
Replies: 44
Views: 6,895
Posted By mmgio

to the op.If it hesitates right after you start...

to the op.If it hesitates right after you start it from cold it probably isn't your o2 sensor.They come in to play when the car reaches normal operating temp.You may have a bad injector or a coil...
Forum: 4th Generation Maxima (1995-1999)
07-23-2012, 04:12 PM
Replies: 10
Views: 839
Posted By mmgio

if it cranks over just fine it is not your...

if it cranks over just fine it is not your starter.If it cranks slow like a dead battery and the battery is good it could be the starter or corroded terminals,corrosion in the battery cables.You...
Forum: 4th Generation Maxima (1995-1999)
07-23-2012, 04:00 PM
Replies: 29
Views: 2,511
Posted By mmgio

for the battery in the trunk you need a deep...

for the battery in the trunk you need a deep cycle battery.A regular battery in the trunk is worthless.Optima bill is right on the money with his comments.Your best bet would be to get a high output...
Forum: 4th Generation Maxima (1995-1999)
05-04-2012, 02:40 PM
Replies: 11
Views: 2,204
Posted By mmgio

Are there any codes? If I had to guess it could...

Are there any codes? If I had to guess it could be your maf sensor.A bad maf could put you in limp mode which sounds like what your car is doing.Also there is an adjustment for your tps sensor.You...
Forum: 4th Generation Maxima (1995-1999)
05-02-2012, 03:23 PM
Replies: 3
Views: 1,492
Posted By mmgio

The reason I wanted to tighten it to spec is...

The reason I wanted to tighten it to spec is because some people had problems with monroe leaving the nut too loose and the struts making a bumping noise going over bumps. Thanks for the responses...
Showing results 1 to 25 of 79
 
Page 1 of 4
1
2
3
Last »


 
Forum Jump


All times are GMT -7. The time now is 08:39 PM.