Maxima Forums

Search: Posts Made By: dillonm695
Showing results 1 to 16 of 16
Search took 0.16 seconds.
Forum: Infiniti I30/I35
03-28-2005, 06:46 AM
Replies: 3
Views: 897
Posted By dillonm695

When I fill it all the way to 3/4 tank, it...

When I fill it all the way to 3/4 tank, it doesn't leak that I can see. When it's filled, there will be a steady drip of highly flammable and explosive gasoline! So I've been keeping it less than...
Forum: Infiniti I30/I35
03-28-2005, 06:39 AM
Replies: 28
Views: 1,234
Posted By dillonm695

I'd say it's time to clean and lube every part of...

I'd say it's time to clean and lube every part of the accelerator pedal to throttle body linkage assembly (i.e. everything mechanical that has to do with accelaration). The only other possibility is...
Forum: Infiniti I30/I35
03-21-2005, 01:42 PM
Replies: 27
Views: 1,633
Posted By dillonm695

I agree that the gas pedal is too far to the...

I agree that the gas pedal is too far to the right, and its relationship to the other pedals is off, or maybe it's the seat position that is off. Regardless, the ergonomics of the whole seat/pedals...
Forum: Infiniti I30/I35
03-21-2005, 12:18 PM
Replies: 3
Views: 897
Posted By dillonm695

leaking fuel from fuel gauge sender assmbly

My '96 I30, 145k miles, is leaking fuel. Whenever the tank is filled about 3/4, it will drip gasoline from the top of the fuel tank, where the connections and assembly are for the fuel gauge sender...
Forum: 4th Generation Maxima (1995-1999)
02-27-2005, 04:48 PM
Replies: 4
Views: 576
Posted By dillonm695

Cost of new boots vice axle replacement

An excellent question. Considering the time I spent (probably at least six hours) and the $ (about $20) I don't think that I came out ahead (I think that my time is worth about $50 per hour), if a...
Forum: 4th Generation Maxima (1995-1999)
02-26-2005, 09:27 PM
Replies: 4
Views: 576
Posted By dillonm695

Finally finished this job tonight. Rented a...

Finally finished this job tonight. Rented a puller/slide hammer combo from Autozone, got access to a huge bench mounted vice, and that outer joint just popped right off. Once again, it really pays...
Forum: 4th Generation Maxima (1995-1999)
02-26-2005, 09:20 PM
Replies: 10
Views: 9,836
Posted By dillonm695

I just finished replacing the upper oil pan...

I just finished replacing the upper oil pan gasket and rear crank seal on my I30. I did it because I had pulled the tranny to replace the clutch, and found evidence of weeping at the oil seal. The...
Forum: 4th Generation Maxima (1995-1999)
02-26-2005, 09:09 PM
Replies: 6
Views: 707
Posted By dillonm695

A quick way to isolate a draw is to pull fuses...

A quick way to isolate a draw is to pull fuses and relays, and measure the current draw across the connections. If you have the hood open while doing this, use tape or something to hold down the...
Forum: 4th Generation Maxima (1995-1999)
02-23-2005, 07:59 PM
Replies: 4
Views: 576
Posted By dillonm695

Outer CV Joint Removal

I'm trying to pull off the outer CV joint on the right axle, and this thing is really kicking my butt!

I've read the FAQ webpage, and the procedure described is exactly like the factory service...
Forum: Infiniti I30/I35
02-21-2005, 08:02 PM
Replies: 11
Views: 2,241
Posted By dillonm695

Thanks to all who offered advice. This past...

Thanks to all who offered advice. This past weekend I dove in, and pulled the tranny. It was a royal pain, and the factory service manual (FSM) is not complete WRT all the things that require...
Forum: 4th Generation Maxima (1995-1999)
02-17-2005, 08:01 PM
Replies: 2
Views: 396
Posted By dillonm695

Thanks, bullfrog! Exactly the info I was...

Thanks, bullfrog!

Exactly the info I was looking for (and hoping to hear - don't really need the special tool if one is persistent).

Max
Forum: 4th Generation Maxima (1995-1999)
02-16-2005, 07:19 PM
Replies: 2
Views: 396
Posted By dillonm695

special tool for axle seals??

Need a little help here. My car is a '96 Infiniti I30 w/ five speed manual tranny, 145k miles.

I've got to pull the transmission, as the clutch has started slipping. I've got the factory service...
Forum: Infiniti I30/I35
02-16-2005, 07:14 PM
Replies: 11
Views: 2,241
Posted By dillonm695

slipping clutch - how adjust engagement point?

DoubleE,

Thanks for the tips. Actually, my car has about 145k miles, and I bought it used with about 80k miles on it in 1999. I think that it is the original clutch; it was very tough to get a...
Forum: Infiniti I30/I35
02-05-2005, 10:08 AM
Replies: 11
Views: 2,241
Posted By dillonm695

How do I adjust clutch engagement point?

I'd love to try that -- please point me in the right direction.

TIA,
Max
Forum: Infiniti I30/I35
01-29-2005, 01:49 PM
Replies: 11
Views: 2,241
Posted By dillonm695

Slipping clutch - what's the problem?

The clutch has begun slipping in my car ('96 I30 with five speed manual tranny). In 4th or 5th gear, if I floor the gas peddle, the clutch will slip for a bit (engine speed will climb faster than...
Forum: Infiniti I30/I35
01-29-2005, 01:41 PM
Replies: 0
Views: 604
Posted By dillonm695

Driveshaft seal installation tool??

Need a little help here. My car is a '96 I30 w/ five speed manual tranny.

I've got to pull the transmission, as the clutch has started slipping. I've got the factory service manual, and in the...
Showing results 1 to 16 of 16


 
Forum Jump


All times are GMT -7. The time now is 11:06 AM.