Maxima Forums

Search: Posts Made By: denclock
Showing results 1 to 15 of 15
Search took 0.01 seconds.
Forum: 3rd Generation Maxima (1989-1994)
04-26-2014, 06:59 PM
Replies: 15
Views: 1,867
Posted By denclock

I'm having the same problem. 1,2, and 3 work...

I'm having the same problem. 1,2, and 3 work fine, 4 doesn't. I found what I thought was the high blower relay in the passengers side kick panel, and tried to test it. I keep getting continiutiy. I...
Forum: 3rd Generation Maxima (1989-1994)
04-05-2014, 03:09 PM
Replies: 2
Views: 696
Posted By denclock

Various Line questions with Pictures

I am trying to figure out what these lines are for. And also want to make Sure they are attached at the right place.

I found this line, and metal U just laying on the driver side, going from a...
Forum: 3rd Generation Maxima (1989-1994)
11-21-2013, 08:06 PM
Replies: 7,152
Views: 541,279
Posted By denclock

Not sure if I should have edited my last post but...

Not sure if I should have edited my last post but since it is different, thought I would make a separate post.

Edit:I found a picture for the iacv. So I deleted this question.
Forum: 3rd Generation Maxima (1989-1994)
11-17-2013, 10:12 AM
Replies: 7,152
Views: 541,279
Posted By denclock

Another noob type question, and thanks jbbons for...

Another noob type question, and thanks jbbons for all your help.

yesterday I was trying to ohm the injector that is in the center of the rail. I had difficulty doing that but I think i got a 12...
Forum: 3rd Generation Maxima (1989-1994)
09-02-2013, 12:14 AM
Replies: 7,152
Views: 541,279
Posted By denclock

Ok, then I have another hose that I connected to...

Ok, then I have another hose that I connected to the heater control valve, and it comes from right under the heater control valve, and it is skinny, and short. you have any on that one? Thanks...
Forum: 3rd Generation Maxima (1989-1994)
09-01-2013, 10:19 PM
Replies: 7,152
Views: 541,279
Posted By denclock

Not a complete noob, but this seemed like a noob...

Not a complete noob, but this seemed like a noob question. Looking down at the fuel injection system from the front of the car, what is the Skinny vacuum hose that is coming out of intake/fuel...
Forum: 3rd Generation Maxima (1989-1994)
08-19-2013, 02:17 AM
Replies: 37
Views: 16,152
Posted By denclock

Ok Update: My car went into fail safe mode...

Ok Update: My car went into fail safe mode today, and it has done it before, I just didn't recognize it as that until today, thanks to the forum. It would rev past 2500 when I put it in park, but...
Forum: 3rd Generation Maxima (1989-1994)
08-16-2013, 12:27 PM
Replies: 37
Views: 16,152
Posted By denclock

I am having a similar issue. I have had 2...

I am having a similar issue. I have had 2 injectors replaced, all new belts, almost all gaskets replaced, Cts, and gauge temp sensors replaced, and a new radiator cap. I am hoping mine is a simple...
Forum: 3rd Generation Maxima (1989-1994)
08-13-2013, 10:14 AM
Replies: 15
Views: 2,754
Posted By denclock

It has no issues at higher revs. it is at idle...

It has no issues at higher revs. it is at idle when it is boiling over, and over heating(maybe). Yesterday, when I first crank the car, i had the radiator off, and I could not tell if it water was...
Forum: 3rd Generation Maxima (1989-1994)
08-13-2013, 10:08 AM
Replies: 16
Views: 9,181
Posted By denclock

The vent inserts are on the plastic trim. I got...

The vent inserts are on the plastic trim. I got scared thinking I was going to break them, and put it all back.
Forum: 3rd Generation Maxima (1989-1994)
08-11-2013, 10:12 AM
Replies: 15
Views: 2,754
Posted By denclock

So they are both attached to that hose? the one...

So they are both attached to that hose? the one Facing the firewall is the ects, the one pointed towards the radiator is the temp gauge switch? Reason I am curious is I am probably going to get both,...
Forum: 3rd Generation Maxima (1989-1994)
08-10-2013, 10:08 AM
Replies: 15
Views: 2,754
Posted By denclock

Did you try to fix it, or just didn't bother? ...

Did you try to fix it, or just didn't bother? Thanks for letting me know.



I called my local autozone, and they have the same one listed for each name. Are they both the same part? If not,...
Forum: 3rd Generation Maxima (1989-1994)
08-09-2013, 03:39 PM
Replies: 16
Views: 9,181
Posted By denclock

My Odometer, and trip do not work, I can hear it...

My Odometer, and trip do not work, I can hear it clicking, but I am not sure what to do to fix it, all other gauges on the cluster work fine. A mechanic said that the gears may have slipped out of...
Forum: 3rd Generation Maxima (1989-1994)
08-09-2013, 03:10 PM
Replies: 15
Views: 2,754
Posted By denclock

Thanks for clearing that up. I googled it, and...

Thanks for clearing that up. I googled it, and was thinking that is the computer I might not be up to this challenge. lol I tried to look under the hood yesterday to see if I could find the Coolant...
Forum: 3rd Generation Maxima (1989-1994)
08-09-2013, 10:38 AM
Replies: 15
Views: 2,754
Posted By denclock

I am having the same issue with my '90 SE. Did he...

I am having the same issue with my '90 SE. Did he ever resolve his issue? I am starting to really drive, and use my Maxima after having it for several years. It set for a while, so I had several...
Showing results 1 to 15 of 15


 
Forum Jump


All times are GMT -7. The time now is 10:48 AM.