Maxima Forums

Search: Posts Made By: spete239
Showing results 1 to 11 of 11
Search took 0.03 seconds.
Forum: 5th Generation Maxima (2000-2003)
04-07-2012, 01:20 PM
Replies: 135
Views: 110,209
Posted By spete239

Ok , after fixing some mistakes, back to square...

Ok , after fixing some mistakes, back to square one,no start with sensor plugged in, after start I plug in sensor in, have tach working, I have voltage to sensor (13.96v when running) 12v with key...
Forum: 5th Generation Maxima (2000-2003)
04-05-2012, 02:10 PM
Replies: 135
Views: 110,209
Posted By spete239

OK, no signal(voltage) at pin 95 on emc, will be...

OK, no signal(voltage) at pin 95 on emc, will be doing continuity test, besides doing the short test on the ckp sensor can I hot wire it and pass a screwdriver by it?
Forum: 5th Generation Maxima (2000-2003)
04-01-2012, 01:36 PM
Replies: 135
Views: 110,209
Posted By spete239

OK, Ya I hear u, thought the same, I did do some...

OK, Ya I hear u, thought the same, I did do some testing good thing, well I knew there was a splice up by engine cowl that I confirmed was right last week, today though I found another splice before...
Forum: 5th Generation Maxima (2000-2003)
03-31-2012, 07:21 PM
Replies: 135
Views: 110,209
Posted By spete239

To test ck crank sensor u need a scope, no ohms...

To test ck crank sensor u need a scope, no ohms or test with a screw driver sensor hooked up and pass a screwdriver pass it and get voltage reading, I will do that I think it either 5 or 12 v. I...
Forum: 5th Generation Maxima (2000-2003)
03-31-2012, 04:13 PM
Replies: 135
Views: 110,209
Posted By spete239

Signal plate look dead center of sensor opening...

Signal plate look dead center of sensor opening and when cranking over runs true, what I notice is where the Bell housing and engine meet to create the sensor opening they are not flush, engine is...
Forum: 5th Generation Maxima (2000-2003)
03-30-2012, 03:33 PM
Replies: 135
Views: 110,209
Posted By spete239

2nd Dealer not much help, said number on crank...

2nd Dealer not much help, said number on crank sensor are manufacturer number, suggested nissan motorsport site might be able to get engine vin # info.
being a newbe( Dealer never heard of...
Forum: 5th Generation Maxima (2000-2003)
03-28-2012, 06:12 PM
Replies: 135
Views: 110,209
Posted By spete239

BTW I took out crank sensor to bring with me,...

BTW I took out crank sensor to bring with me, this is a new one the guy tried. but gave info for an 2002 # A29662-L33, looking at Nissan parts site looks like they go to 02, then 03 to present so 5.5...
Forum: 5th Generation Maxima (2000-2003)
03-27-2012, 05:55 PM
Replies: 135
Views: 110,209
Posted By spete239

Thanks, I'll try it

Thanks, I'll try it
Forum: 5th Generation Maxima (2000-2003)
03-27-2012, 02:11 PM
Replies: 135
Views: 110,209
Posted By spete239

yes on codes po725 and crank shaft position...

yes on codes po725 and crank shaft position sensor. dealer didnt give that code, tach wont work when crank senor is unpluged
Forum: 5th Generation Maxima (2000-2003)
03-27-2012, 01:55 PM
Replies: 135
Views: 110,209
Posted By spete239

Yes it runs good, just being in NY wont pass...

Yes it runs good, just being in NY wont pass insp, correction I would replace both cam sensors, but not sure of eng year, could I cross ref the existing ones which I think came with donor eng.
Forum: 5th Generation Maxima (2000-2003)
03-26-2012, 04:54 PM
Replies: 135
Views: 110,209
Posted By spete239

unplug crank sensor car starts

Starts with crank sensor unplugged after cycleing 5-6 time and not turning key to OFF position
02 Maxima, auction car, determined engine was swapped verified by Nissan. dealer said they could not...
Showing results 1 to 11 of 11


 
Forum Jump


All times are GMT -7. The time now is 09:27 PM.