VA 97 Full swap (nearly) Va $3000

sergofast · 2014-01-06 21:29:31

image | Flickr - Photo Sharing!@@AMEPARAM@@http://farm4.staticflickr.com/3795/11873583163_670c558fd4_m.jpg@@AMEPARAM@@http://farm4.staticflickr.com/3795/11873583163_670c558fd4@@AMEPARAM@@11873583163@@AMEPARAM@@670c558fd4@@AMEPARAM@@jpg@@AMEREPLACE@@ image | Flickr - Photo Sharing!@@AMEPARAM@@http://farm4.staticflickr.com/3774/11873584503_b6deef7f4d_m.jpg@@AMEPARAM@@http://farm4.staticflickr.com/3774/11873584503_b6deef7f4d@@AMEPARAM@@11873584503@@AMEPARAM@@b6deef7f4d@@AMEPARAM@@jpg@@AMEREPLACE@@ 97 Maxima in Virginia – $2500 for everything below minus the stuff listed at the bottom. If this doesnt sell Im parting it out. The good: Koni Yellows (front strut shortened an inch) Progress Springs and an extra set of Eibachs Progress Rear sway bar Rear beam is bent to zero toe for better handling Subframe connectors welded on. 3” Catman Catback with Fast cat converter Front and rear strut bar 00vi conversion Interior is in excellent shape for age/mileage of car. Black on Black. Tinted windows Blemco Stage 2 lower frame stiffener ES bushing, Whiteline bushings (increases caster in the front), Delrin lower control arm bushings) HID headlights with TL projectors and upgraded lenses. 01 SE VLSD Tranny Fidanza Lightened flywheel The bad: 3.0 Engine has 230k on it and has a bad dead spot (I think it’s a coil pack or injector). It also loses about a quart of oil every 4k miles. I would suggest dropping a new engine in it. (see below). It still runs just fine enought to reliabily get you rfrom a to b so you can drive this home. Steering rack needs to be replaced along with the steering rack rubber brackets. Extra parts (not included with sale of car but are complete): VQ35 engine with 65k on it - $500 Catman Gen 2 headers - $500 Kevlo LED light boards - $300 Complete wiring harness and all associated parts for full swap. This includes: dash gauges, pedal, ignition switch, ECU, custom timing ring for 5speed tranny, extra ECU brackets, Engine harness, and NEARLY completed conversion harness (see the attached thread). The only piece I have not completed of the conversion harness is the power portion of the harness…everything else is complete and I just don’t have the time to finish the project. http://forums.maxima.org/all-motor/628396-full-swap-harness.html - $500

Reply Subscribe

Thread Tools

Search this Thread

01-06-2014, 01:29 PM

sergofast

Supporting Maxima.org Member

Thread Starter

iTrader: (22)

Join Date: Jul 2005

Location: Ashburn, VA

Posts: 985

97 Full swap (nearly) Va $2500

http://www.flickr.com/photos/113675646@N06/11873583163/http://www.flickr.com/photos/113675646@N06/11873584503/
97 Maxima in Virginia – $2500 for everything below minus the stuff listed at the bottom. If this doesnt sell Im parting it out.

The good:

Koni Yellows (front strut shortened an inch)
Progress Springs and an extra set of Eibachs
Progress Rear sway bar
Rear beam is bent to zero toe for better handling
Subframe connectors welded on.
3” Catman Catback with Fast cat converter
Front and rear strut bar
00vi conversion
Interior is in excellent shape for age/mileage of car.
Black on Black.
Tinted windows
Blemco Stage 2 lower frame stiffener
ES bushing, Whiteline bushings (increases caster in the front), Delrin lower control arm bushings)
HID headlights with TL projectors and upgraded lenses.
01 SE VLSD Tranny
Fidanza Lightened flywheel

The bad: 3.0 Engine has 230k on it and has a bad dead spot (I think it’s a coil pack or injector). It also loses about a quart of oil every 4k miles. I would suggest dropping a new engine in it. (see below). It still runs just fine enought to reliabily get you rfrom a to b so you can drive this home.
Steering rack needs to be replaced along with the steering rack rubber brackets.

Extra parts (not included with sale of car but are complete):

VQ35 engine with 65k on it - $500
Catman Gen 2 headers - $500
Kevlo LED light boards - $300
Complete wiring harness and all associated parts for full swap. This includes: dash gauges, pedal, ignition switch, ECU, custom timing ring for 5speed tranny, extra ECU brackets, Engine harness, and NEARLY completed conversion harness (see the attached thread). The only piece I have not completed of the conversion harness is the power portion of the harness…everything else is complete and I just don’t have the time to finish the project. http://forums.maxima.org/all-motor/6...p-harness.html - $500

Last edited by sergofast; 01-11-2014 at 09:34 PM. Reason: Price drop

01-06-2014, 04:58 PM

Excalibur23

Member

iTrader: (3)

Join Date: Mar 2011

Location: Levittown, PA

Posts: 288

Glws, just pmed you

01-07-2014, 10:05 AM

sergofast

Supporting Maxima.org Member

Thread Starter

iTrader: (22)

Join Date: Jul 2005

Location: Ashburn, VA

Posts: 985

Thanks. I got your PM. Give me a call.

01-13-2014, 11:03 PM

Slamrod

Newbie - Just Registered

iTrader: (11)

Join Date: Apr 2013

Location: Long Island, NY

Posts: 1,169

Man if i was closer id probably buy this and swap a new engine in. Basically everything i want in a max..

GLWS and worst comes to worst me and others will eat up those parts like candy

01-14-2014, 03:53 AM

Max streets

Senior Member

iTrader: (11)

Join Date: Sep 2012

Location: NYC

Posts: 605

U never posted how far u got on the swap harness.more info on that please.

02-04-2014, 09:07 AM

mjmauro484

Newbie - Just Registered

Join Date: Jan 2014

Posts: 10

Do you still have the VQ35 for sale?

03-24-2014, 06:46 PM

maxprivate

Black Lion

iTrader: (12)

Join Date: Sep 2005

Location: NJ, Down by the River

Posts: 2,684

what happened to your project?

04-09-2014, 07:41 PM

sergofast

Supporting Maxima.org Member

Thread Starter

iTrader: (22)

Join Date: Jul 2005

Location: Ashburn, VA

Posts: 985

I just didn't have time to finish it but the harness is nearly complete. The only part that has to be worked out is the 12v power portion and I'm selling everything to one lucky forum member that wants to by all my full swap parts. $300 plus shipping.