Group Deals / Sponsors ForumFind out more information on group deals that are going on for Maxima parts from our Sponsors.
Welcome to Maxima.org!
Welcome to Maxima.org,
You are currently viewing our forum as a guest, which gives you limited access
to view most discussions and access our other features. By joining our community, at no cost, you will have access to start new topics, reply to conversations, privately message other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, so please join Maxima.org today!
im sorry but what is your setup
and all i really need to know is what year car and single or dual output and how many secondary o2 sensors you have
-Jared
Headers / Y Pipe / Catback. I have two sensors that are plugged in behind the catalytic converter in the Y-pipe. Those two previously were in the stock manifolds before I got the headers. So is one enough or do I need two?
Headers / Y Pipe / Catback. I have two sensors that are plugged in behind the catalytic converter in the Y-pipe. Those two previously were in the stock manifolds before I got the headers. So is one enough or do I need two?
one should be find since they are dual output. that way you can bypass the secondary's, the sims im selling are dual output
-The harness you need is under the carpet under the driver's seat. Remove the seat to get better access. The harness will be a 4-wire connector beneath the big hole in the carpet.
-Note: Do all connections in FRONT of the connector, where the wires are distinctively color-coded. There are four wires: black, white, red, and red/black.
1. The black wire from the o2 simulator TAPS into the black wire on the harness.
2. The red wire from the o2 simulator TAPS into the red/black wire on the harness.
3. The white wire from the o2 simulator (these simulators have two white wires for dual output, just use one and disregard the other. i just cut the extra off) INTERCEPTS the white wire on the harness.
4. The red wire on the harness is left untouched.
5. Make sure to plug the harness back into the o2 sensor so the heater on the o2 works, otherwise you'll throw a CEL for a heater malfunction code.
-Turn the key to "on" and makes sure the little LED on the simulator blinks. Solder all connections, wrap them up, tuck everything under the carpet, reinstall driver's seat. Done!
-Note: This was done on a '97, may be different for other years but I doubt it.
o and the packaging, yea, these little things are very durable so packing bubbles are not necessary. Unless they threw it off a building and rolled over it while it was standing on its side
I got mine today, just hoping that they are ok since they come in a regular mail envolpe. It was pretty beat up.
How do you install these? There is no instructions or labels on the wires. Thanks.
Ferhan
Yeah, no offense but dang, they could have at least put it in some bubble wrap. It's a tiny circuit board. I'd have paid an extra dollar for shipping, to have it wrapped in something more protective than a plastic bag. Mine is a little scratched up, even the bag has some tear in it. I hope it works.
Thanks for posting instruction, took me a minute to even figure out what it was.
I ordered 2 sims but there's only one in the envelope. i'm assuming you sent them seperately.
i am so very sorry, the other one is in the mail. I must have not put both of them in there or i counted improperly or someone got 2 that was supposed to get one. but i will have the other one out in ten minutes i am going to the post office now.
Just for clarification, how many duel sims does a 6th gen need? Unless people are giving the other away as a present do I need 2????
no one should be enough it is used in the secondary position and there are only 2 in that position that i know of u use the two white wires one of them to each
i am so very sorry, the other one is in the mail. I must have not put both of them in there or i counted improperly or someone got 2 that was supposed to get one. but i will have the other one out in ten minutes i am going to the post office now.
-Jared
It's an honest mistake man. Thanks. Do you know if these will work for an audi too?
__________________
01 I30, [5 speed swap][4th gen pedals and master cylinder][OEM clutch][OEM flywheel][ksport coilovers front, D2 coilovers rear][10k hid headlights and fogs][custom WAI][cattman exhaust][tenzo type-M, 19x8.5 +17F, 19x10 +22R][300zx calipers][Cobra 13" drilled and slotted rotors]
5 speed swap myths BUSTED:
1. Both driver and passenger side AUTO axles work fine.
2. AUTO flywheel bolts work fine.
Are these simulators still available? I need this ASAP. From what I've gathered, this is what I need, I have headers with no cats and my CEL is on. Need to get the car inspected this month or New York State will basically own me and impound my car.
__________________
04 Maxima SE 6-sp Journey
96 Eclipse GS-T 5-sp Spyder
you can mount anywhere you would like i prefer the under seat install it is cleaner and no one has to know that you have it...... that is the reason that you got it in the first place right?
Okay so if I understand correctly
This definitely work on a 97 Maxima.
Quote:
Originally Posted by 96nismomaxi
-The harness you need is under the carpet under the driver's seat. Remove the seat to get better access. The harness will be a 4-wire connector beneath the big hole in the carpet.
-Note: Do all connections in FRONT of the connector, where the wires are distinctively color-coded. There are four wires: black, white, red, and red/black.
1. The black wire from the o2 simulator TAPS into the black wire on the harness.
2. The red wire from the o2 simulator TAPS into the red/black wire on the harness.
3. The white wire from the o2 simulator (these simulators have two white wires for dual output, just use one and disregard the other. i just cut the extra off) INTERCEPTS the white wire on the harness.
4. The red wire on the harness is left untouched.
5. Make sure to plug the harness back into the o2 sensor so the heater on the o2 works, otherwise you'll throw a CEL for a heater malfunction code.
-Turn the key to "on" and makes sure the little LED on the simulator blinks. Solder all connections, wrap them up, tuck everything under the carpet, reinstall driver's seat. Done!
-Note: This was done on a '97, may be different for other years but I doubt it.
Stop Global Whining!!!
Linear Mode
