Blehmco rear parallel link kits! (3 gens only)

**Matt93SE** · 03-12-2008, 06:03 PM

Due to the response I received in the 3 gen forum about a GD on these, here you go..

Regular price, $375 + ship
GD price, $335 + ship

I'll need 5 people minimum for this, and it's going to take approx 3-4 weeks after GD ends to be able to ship everything. I'll open for orders until the end of March, at which point I'll place an order for all of the parts and get them together. 1/2 of payment will be due to put your name on a set, the other 1/2 will be due when I'm ready to ship the parts.

questions?

goon9 · 03-12-2008, 07:06 PM

how much is shipping to 30566?

**Matt93SE** · 03-12-2008, 07:57 PM

$15 via UPS.. Fawk their rates have gone up with the fuel hike...

*4signs* · 03-13-2008, 10:49 PM

put me down for a set Matt, just let me know when to send the deposit

***Jeff92se*** · 03-13-2008, 10:56 PM

Matt. Try to fit them into a flat rate type box from USPS. If I could have shipped my bulk order of brackets inside a small flat rate box, it would have been $12 vs $24.

**Matt93SE** · 03-14-2008, 08:54 PM

Too long to go in a flat rate box. they'll go in a triangle tube though. but also for the price, I trust UPS to get them there more than I do USPS. insurance is cheaper through them as well.

believe me, I've been through it all 500 times.

There's certain things I ship USPS and some UPS.

goon9 · 03-19-2008, 08:58 PM

15 bucks isn't bad at all. Got any buyers???

**Matt93SE** · 03-21-2008, 04:01 PM

you and 4 signs.. in that thread on the 3 gen forum, there were 6 people asking me to do the GD.. now that I'm doing it, nobody's stepping up.. surprise!

goon9 · 03-21-2008, 06:04 PM

Quote:

Originally Posted by Matt93SE

you and 4 signs.. in that thread on the 3 gen forum, there were 6 people asking me to do the GD.. now that I'm doing it, nobody's stepping up.. surprise!

I think I know someone that will get a set, just a matter of me buggin him.

*4signs* · 03-21-2008, 07:46 PM

come on people this is a killer mod

**Matt93SE** · 03-24-2008, 01:19 PM

Why don't you guys go whore this thread out... I can't advertise elsewhere, but you guys can.

dead2fall · 03-26-2008, 06:02 PM

hey im in

sign me up

**Matt93SE** · 03-27-2008, 01:51 PM

1. 4signs
2. dead2fall

Goon, are you in, or just talking ish?

goon9 · 03-29-2008, 05:40 PM

Quote:

Originally Posted by Matt93SE

1. 4signs
2. dead2fall

Goon, are you in, or just talking ish?

I wish I was... I tried making my own and though it may work... It's costing me alot more work and money

I really should of got a set.

**Matt93SE** · 03-30-2008, 08:59 AM

that's how it usually goes...

goon9 · 03-30-2008, 12:55 PM

Quote:

Originally Posted by Matt93SE

that's how it usually goes...

I probably could return the parts I bought, but I already modified my crossmember

and finished working on my hubs today.

I'd like to show you what I did though...

**Matt93SE** · 03-30-2008, 09:28 PM

unless you chopped on it to lower your roll center, you shouldn't have had to mess with the crossmember at all.

goon9 · 03-31-2008, 02:41 PM

Quote:

Originally Posted by Matt93SE

unless you chopped on it to lower your roll center, you shouldn't have had to mess with the crossmember at all.

Because I'm lowered like 1.6" or something like that, I went and raised the mounting points up and set it further towards the center for the longer links I had. I could post a pic here or discuss it in the suspension board... Don't know how much whoring you want in here.

Raising the mounting point should restore the link to the stock angle, or real close.

**Matt93SE** · 04-08-2008, 08:59 AM

go ahead and post up in the suspension forum... I'd like to see how you did it- I've been thinking about doing the same myself, but just haven't found the time to care much recently. work is KILLING me right now.

LukeT · 05-09-2008, 12:26 AM

Count me in if this happens.