98 with a 3.5 swap
#1
98 with a 3.5 swap
I went to the track last friday for test and tune. I wanted to get a baseline to see where I am. My first run ended up being my best run. The car was heat soaked from driving 3 hours plus renting the dyno for an hour before the track. I was able to get one run in when the car had cooled off, but I spun so badly I ran a 14.0x
rt .419
60' 2.150
330 5.794
1/8 8.769
mph 82.50
1000 11.309
1/4 13.442
mph 105.60
I was running at full street trim minus a spare tire and jack. The car is a 98 GXE with full leater i30 interior. I was running on my 18" enkei RP02's. Now the stuff that you guys want to know:
3.5 swap
VLSD tranny
JWT S1 knockoff cams
JWT POP charger
NWP spacers and BOP (otherwise stock FWD intake manifold)
JWT ECU
VAFCII
OBX headers
Catco high flow cat
Cattman 3" exhaust
Over all I am very happy with the results, I think 12's are possible just with smaller wheels and tires. I had traction problems the whole night, but once the car cooled down when I shifted to second at redline it felt like I was doing a rolling burn out I am even spinning 3rd gear pretty hard which was surprising to me. Next time I go to the track I will have tires. I also think I may see good gains from a SSIM. I have a few videos but of course I don't have my best run. I'll try to get them up soon. Post away.
rt .419
60' 2.150
330 5.794
1/8 8.769
mph 82.50
1000 11.309
1/4 13.442
mph 105.60
I was running at full street trim minus a spare tire and jack. The car is a 98 GXE with full leater i30 interior. I was running on my 18" enkei RP02's. Now the stuff that you guys want to know:
3.5 swap
VLSD tranny
JWT S1 knockoff cams
JWT POP charger
NWP spacers and BOP (otherwise stock FWD intake manifold)
JWT ECU
VAFCII
OBX headers
Catco high flow cat
Cattman 3" exhaust
Over all I am very happy with the results, I think 12's are possible just with smaller wheels and tires. I had traction problems the whole night, but once the car cooled down when I shifted to second at redline it felt like I was doing a rolling burn out I am even spinning 3rd gear pretty hard which was surprising to me. Next time I go to the track I will have tires. I also think I may see good gains from a SSIM. I have a few videos but of course I don't have my best run. I'll try to get them up soon. Post away.
#5
Me too. I just did not have enough time to get everything together. Since I was already driving a few hours away to dyno, I was just trying to tie everything together while I was in the area. I still need to figure out the smallest wheel I can fit over my 12.8" brakes/with superlites. Even with these times I was surprising a lot of people, a lot of people were surprised when I had my hood poped and I did not have any forced induction
#6
#7
if i dont sell mine, hit me up w/ some numbers....either way if i keep this car i need to drop in a motor..DE-k cheap way, but if i can get a 3.5 swapped in in a weekend for about the same i'm game
got local issues that prevent me from being able to get an engine put in my car right now. let me know, seriously
got local issues that prevent me from being able to get an engine put in my car right now. let me know, seriously
#9
#10
#11
#15
no time soon. I want to get this n/a set up a little bit faster then I will do the s/c. I want to see 12's n/a.
SSIM will probably be my next mod when I have some time, and I will have slicks before I go to the track again. I kinda doubt I will do emanage, but you never know.
SSIM will probably be my next mod when I have some time, and I will have slicks before I go to the track again. I kinda doubt I will do emanage, but you never know.
#17
#19
#26
They do, but they're rare. http://moesperformance.com/index.php...ducts_id=12401
Of course, I'm not so sure about buying tires from a company where no one knows how to spell 'diameter'.
Of course, I'm not so sure about buying tires from a company where no one knows how to spell 'diameter'.
#27
They do, but they're rare. http://moesperformance.com/index.php...ducts_id=12401
Of course, I'm not so sure about buying tires from a company where no one knows how to spell 'diameter'.
Of course, I'm not so sure about buying tires from a company where no one knows how to spell 'diameter'.
#28
http://www.turbobuick.com/forums/par...0r17s-new.html
saw these while surfing the org, you may be interested
saw these while surfing the org, you may be interested
#29
http://www.turbobuick.com/forums/par...0r17s-new.html
saw these while surfing the org, you may be interested
saw these while surfing the org, you may be interested
#34
#36