6th gen Maxima Mods 0-60 4.9?
09-02-2011, 10:52 PM
#1
Junior Member
Thread Starter
Join Date: Aug 2011
Posts: 32
6th gen Maxima Mods 0-60 4.9?
This maxima pulls in like 4.9 seconds. I really don't like the stock Maxima that pulls in 6.3, it wont cut it. It appears that the only mod he claims to have made [that would make it pull like this] is Utec tune( base Z map). He claims he received lots of low rev torque and pull. The blockoff plate w/ spacers he bought
were not as good as the Stock so that doesn't really matter.
How much is the Utec Tune cost and how do you do it? Complete scrub, thank you.
09-03-2011, 03:57 AM
#2
This maxima pulls in like 4.9 seconds. I really don't like the stock Maxima that pulls in 6.3, it wont cut it. It appears that the only mod he claims to have made [that would make it pull like this] is Utec tune( base Z map). He claims he received lots of low rev torque and pull. The blockoff plate w/ spacers he bought
were not as good as the Stock so that doesn't really matter.
How much is the Utec Tune cost and how do you do it? Complete scrub, thank you.
"Another 6th gen maxima 0-60 or so
Mods: CAI, blockoff plate w/ spacers, y-pipe, catback, gutted cats, and Utec tune( base Z map).
. I have not yet dyno tune the utec, I'm just using the base z map for now, but she is pulling harder now. I had to feather in the pedal due to too much wheel spin, just the base 350z map seems to have added a noticeable torque gain in low to midrange. Also note that the stock manifold w/blockoff plate seems to pull much harder and is more responsive than the kinetix(sold) according to butt dyno."
09-03-2011, 11:19 AM
#4
09-04-2011, 07:48 PM
#6
Junior Member
Thread Starter
Join Date: Aug 2011
Posts: 32
Learn to read fool.
"Another 6th gen maxima 0-60 or so
Mods: CAI, blockoff plate w/ spacers, y-pipe, catback, gutted cats, and Utec tune( base Z map).
. I have not yet dyno tune the utec, I'm just using the base z map for now, but she is pulling harder now. I had to feather in the pedal due to too much wheel spin, just the base 350z map seems to have added a noticeable torque gain in low to midrange. Also note that the stock manifold w/blockoff plate seems to pull much harder and is more responsive than the kinetix(sold) according to butt dyno."
"Another 6th gen maxima 0-60 or so
Mods: CAI, blockoff plate w/ spacers, y-pipe, catback, gutted cats, and Utec tune( base Z map).
. I have not yet dyno tune the utec, I'm just using the base z map for now, but she is pulling harder now. I had to feather in the pedal due to too much wheel spin, just the base 350z map seems to have added a noticeable torque gain in low to midrange. Also note that the stock manifold w/blockoff plate seems to pull much harder and is more responsive than the kinetix(sold) according to butt dyno."
I ASKED how much would it cost to do a "Utec tune( base Z map" and what exactly is this. LEARN how to read what i asked before you call me a fool.
09-04-2011, 07:59 PM
#7
I used this calculator to figure out my 0-60 time. I don't know how accurate it is, but take it for what it's worth.
With an 1/8th mile of 8.3 at 84mph my 0-60 time is 4.23 seconds.
Traction is key to good 0-60 times.
With an 1/8th mile of 8.3 at 84mph my 0-60 time is 4.23 seconds.
Traction is key to good 0-60 times.
Thread
Thread Starter
Forum
Replies
Last Post
Lakersallday24
6th Generation Maxima (2004-2008)
13
03-20-2024 11:22 AM
morteljc
7th Generation Classifieds (2009-2015)
15
10-19-2015 10:47 AM
Finkle
4th Generation Maxima (1995-1999)
13
09-27-2015 09:53 PM