FS: 5.5 Gen HID Headlight, Eyelid, and Smoked Sidemarker
08-15-2007, 01:32 PM
#1
FS: 5.5 Gen HID Headlight, Eyelid, and Smoked Sidemarker
Some interesting things here for sale lol...
I need this stuff GONE asap it's been sitting around and my landlord is not happy!
I have feedback on here along with 22+ on ebay as ati_4life.
Heatware: JessAlba452
Paypal = JessAlba452@hotmail.com
I have an eyelid for a 2002-2003 in Grey Lustre for passenger side. - $10 Shipped
Also a FACTORY Nissan HID headlight for 2k3. Involved in a fender bender so it works but the housing is cracked in various places near the turn signal. Does not hold moisture, so it's still sealed well.
Pardon the adhesive at the top of the light it is there from my driver side eyelid. Will be removed prior to sending out.
Housing is easily replaceable if you can find someone parting out The plastic holding the ballast to the light is also cracked. Can use epoxy to hold secure. The headlight lense is scuffed up, but is repairable. All is needed is to sand the lense down and apply plasticX. One of the tabs where you secure the bolt onto the car is bent, but it's a stress bend as seen in the picture. A heat gun to warm the plastic should be able to bend it back to shape when installing.
Includes Ballast, and all lights. Know that this is in WORKING condition I still drove around at night before the car was in the shop. Turn signal, high beams, Xenons ect work fine. -
(NOTE = Now parting out...HID and Ballast SOLD open to ANY and ALL offers for the headlight)
HID + Ballast + Wiring SOLD
Housing is NOW SOLD!!!
Also a driver side smoked side marker with broken tab - Asking $5
Resonator 5.5 gen with 25,000 miles minor surface rust - Asking $35
Y-pipe with 2.5" connector needs to be welded on at a shop will cost you less than $100 taken off at 30,000 miles includes heatshields and bolts if needed - Asking $50
I need this stuff GONE asap it's been sitting around and my landlord is not happy!
I have feedback on here along with 22+ on ebay as ati_4life.
Heatware: JessAlba452
Paypal = JessAlba452@hotmail.com
I have an eyelid for a 2002-2003 in Grey Lustre for passenger side. - $10 Shipped
Also a FACTORY Nissan HID headlight for 2k3. Involved in a fender bender so it works but the housing is cracked in various places near the turn signal. Does not hold moisture, so it's still sealed well.
Pardon the adhesive at the top of the light it is there from my driver side eyelid. Will be removed prior to sending out.
Housing is easily replaceable if you can find someone parting out The plastic holding the ballast to the light is also cracked. Can use epoxy to hold secure. The headlight lense is scuffed up, but is repairable. All is needed is to sand the lense down and apply plasticX. One of the tabs where you secure the bolt onto the car is bent, but it's a stress bend as seen in the picture. A heat gun to warm the plastic should be able to bend it back to shape when installing.
Includes Ballast, and all lights. Know that this is in WORKING condition I still drove around at night before the car was in the shop. Turn signal, high beams, Xenons ect work fine. -
(NOTE = Now parting out...HID and Ballast SOLD open to ANY and ALL offers for the headlight)
HID + Ballast + Wiring SOLD
Housing is NOW SOLD!!!
Also a driver side smoked side marker with broken tab - Asking $5
Resonator 5.5 gen with 25,000 miles minor surface rust - Asking $35
Y-pipe with 2.5" connector needs to be welded on at a shop will cost you less than $100 taken off at 30,000 miles includes heatshields and bolts if needed - Asking $50
Last edited by Jess; 10-15-2007 at 11:07 PM.
08-16-2007, 09:57 AM
#4
Yes still have them. But it's only the driver side. I MIGHT have a set if I can get it from the shop. I will call and see if it was thrown out or not, just didn't see it when I picked up the headlight.
08-16-2007, 06:13 PM
#6
^
I do...but only if you don't mind one being carbon fibered.
I'd just sand it though and repaint. The reason why I didn't do the other eyelid in CF is that after I did this one it was pretty stiff. Yes it's real CF
First time I've ever done a CF overlay and it was pretty hard.
I do...but only if you don't mind one being carbon fibered.
I'd just sand it though and repaint. The reason why I didn't do the other eyelid in CF is that after I did this one it was pretty stiff. Yes it's real CF
First time I've ever done a CF overlay and it was pretty hard.
10-07-2007, 12:53 PM
#24
I really need everything gone.
Got a speeding ticket that's $200 which I need to pay.
I need a radar/laser detector for those 300 mile trips argh.
So lmk what you guys have to offer! Thanks!
Got a speeding ticket that's $200 which I need to pay.
I need a radar/laser detector for those 300 mile trips argh.
So lmk what you guys have to offer! Thanks!
10-07-2007, 06:39 PM
#26
10-13-2007, 11:40 PM
#33
IN IRAQ MAXIMA.ORG-ING :)
iTrader: (11)
Join Date: Jul 2004
Location: Northern New Jersey
Posts: 1,461
hey bud im interested in the headlight and just one smoked side marker... the rear d.s. lmk im pretty sure the headlight won't come with the ballast and all so im okay with that... shoot me a pm if anything
10-14-2007, 07:58 PM
#34
If anyone needs a better pic of anything feel free to send a PM.
Thread
Thread Starter
Forum
Replies
Last Post
Finkle
4th Generation Maxima (1995-1999)
13
09-27-2015 09:53 PM
sdotcarter
6th Generation Maxima (2004-2008)
2
09-02-2015 09:53 PM